john deere 210

I bought a basket case JD 210 lawn tractor (1986) and went all over it. Got it running, new belts, etc, etc. Mowed with it a couple of times for a total of about 5 or 6 hours. Got it for the wife to use. (she likes it) Runs and mows great. Yesterday it would not start. Starter not kicking in...

Hi i was wondering if anyone had the dimensions of the john deere lift link for the snow plow? or a cheap source?

Hi Everyone. I recently bought a JD 210 for snowblowing my driveway. I'm having issues lowering the lift so that I can attach the linkage from the snowblower to the tractor. I'm wondering if someone could give me steps on how to lower the lift just in case I'm doing it wrong. This is my first...

My 4 year old Simplicity Conquest with 23hp Briggs Vanguard motor blew up. It's in the shop for a few weeks getting diagnosed but I'm very concerned it's dead, spewing oil out the left valve cover and little to no compression. Guy thinks it most likely severely overheated, probably due to a...

Hi, garden tractor 210 (1980s)mower deck is a 46" model munber is 47 I left the shop manual at my house upstate (3 hours away), I brought home the deck to replace bearings in spindles. I am having a hard time removing them. Do I have to remove pulleys in order for spindle housing to be...

I bought a john deere 210 without a mower deck. I got the machine running and now I need to find a deck. Will the 300 series decks fit, because I can find lots of them or am I stuck looking for a 200 series deck?

My 210 C is stuck in first gear. No amount of pulling or pushing on the shift lever will move it. Has anyone experienced this problem. This is a 1990 4X4 with a 4 in 1 front loader and a rear box scrapper with rippers. I'm thinking maybe I can pop the top of the transmission off and look at...

I have a vibration on my 1984 John deere 210. It occurs when the PTO is engaged to the mower deck and it appears to be from the deck belt tension pulleys. Can definitely feel it in the seat. The main bolt that goes into the engine block is good and snug but the pulley bracket has some play at...

I have a vibration on my 1984 John Deere 210. It occurs when the PTO is engaged to the mower deck and it appears to be from the deck belt tension pulleys. Can definitely feel it in the seat. The main bolt that goes into the engine block is good and snug but the pulley bracket has some play at...

I have an '84 John Deere 210. I am trying to replace the metal discharge chute on the 38" deck to a plastic part. I ordered a plastic chute that lines up fine but the existing hinge on the deck won't accept the newer plastic chute design. Wondering if anyone knows of a place I could find a...

Hi all, see video. I picked up a 210 with mower and bagger the other day. Cleaned out the fuel tank, and put in a new battery and this is what it ran like. Am I right to guess that this thing needs rings/piston work badly due to blowby? It shows over 1700 hours on the hobbs meter. Thanks...

So I realize the stearing will be bad, But I got hills and loads to go up them and down them,And only a little 210 to do it with:confused2: Got the tiller ,mower,blower,plow for snow ,trailer,weights and chains,also made a front plow to make my hills for potatos.:dance1: works good. Sean some...

Need 12 ft harrow moved from Moultrie to Newborn, Ga. Any ideas?

Hi All, I'm looking at the 210 loader specs (considering one for my John Deere 2210). The 210 loader has been replaced by the 200CX and I've been wondering what the spec differences between the two loaders are. First off, I can't find what specs for how the 200CX would perform on a John Deere...

Hi All, I'm (hopefully) going to be picking up a 210 loader for my John Deere 2210 SCUT. I'm going to need to ship it via a freight carrier, and one of the things I'll need to know in order to get an accurate shipping estimate is the weight. I've been searching on this and I haven't been able...

would you trade even for a John Deere 210 giving up a Cub Cadet 582 of the same condition which do you think is worth more. Here's the story I bought the 582 cub 5 years ago and it is very nice. The guy I bought it from, bought it new in 1983 I think it is the last year cub built? It is red.The...

Has anyone built a stand for the JD 210 loader on a JD 2210? Looking to remove mine for mowing?

i just bought a JD 210C and was curious if anyone knew what other machines may share the same bucket mount, i wasnt sure if the 310 and 410 used a larger mount or not and figured surely one of you guys has tried this before!

I'm looking at 2 tractors-one with a 210 loader and one with a 200cx. I've looked through several old posts now and I'm curious if there are any new thoughts since the 200cx has been out for a while. I understand that the 200cx is part or mostly cast??? Isn't this going to make for a weaker...

I have a JD 210 garden tractor I am trying to sell but I don't know what year it was manufactured? I asuume there is a way to tell by the serial number is there anybody that can look this up for me?

Howdy folks: New guy here and I am looking for some advice. My JD210 has developed a "Death Rattle" in the engine. The engine is a Kohler model K241AQS. My request is this. Is there a replacement engine that maybe fits it. John Deere no longer sells a complete engine nor does Kohler. Their...

Did anyone install their own 210 loader? Just wondering how many quarts of hydraulic oil had to be added to your 2210 tractor. Thanks, Ken

Looking to buy a JD 2210 with the JD 210 FEL (49 inch bucket) and have not been able to find the specifications for the FEL. Searched the web with no luck and local JD dealer advises JD has yet to put out full, printed spec sheet. Got the lift capacity @ 640 lbs, but not much else. Was wondering...

I'VE JUST INSTALLED NEW BELTS ON MY OLD 210, AS WELL AS SQUARING UP THE MOWER DECK. NOW THERE'S A BIND IN THE CLUTCH, IT DOES NOT RETURN AS FAST AS IT SHOULD. DOES ANYONE KNOW WHAT I'VE DONE? BADPARKER