hydraulic cylinder

  1. S

    Kubota BH75 bent bucket cylinder rod

    Does anyone have the exact specs on the bucket cylinder for a BH75 backhoe? I bent the rod digging in some rocks. A new cylinder from the stealership is almost $1000. I can get a new rod machined, but if I can find a matching cylinder for cheaper, I’d just as soon replace it. I know Kubota...
  2. F

    Massey Ferguson 1525 FEL bucket curl cylinder seal replacement walkthrough

    I looked in many places for a walkthrough for my particular equipment however I didn't find one that was 100% the same. Many tutorials and videos showed 80% similar steps but there were nuances that weren't the same, like the wire retaining clip. Eventually I came to a point where I felt I had...
  3. B

    Seal Kits for MF 30B

    I'm needing to source complete seal kits for all of the cylinders on my MF 30B, but having a bit of trouble. Boom cylinders Bucket cylinders Steering cylinders Is there anyone out there with prior experience and/or a service manual that might be able to tell me what part numbers/distributors I...
  4. K

    gland question

    I am replacing the seals on my Kubota BT600 dipper cylinder. I've only replaced seals on a couple of other cylinders and that was years ago. However I don't remember the other glands having this rough metal (right above the old rod seal). Is this normal? (mute it unless you want to hear my...
  5. F

    Can this hydraulic cylinder be rewelded or do I need to replace?

    Was moving some rocks today when all of a sudden I saw my loader cylinder dangling. Looks like a break at the weld. I am thinking this can just be repaired. Is that the case or do I need to buy a replacement?
  6. D

    what and how would you modify to make new hydraulic cylinder fit?

    Good morning, and happy 4th to everyone! Skip this paragraph if you don't want the back story... I had recently won an auction for a 4 in 1 combo bucket that is rather vintage (melroe/bobcat brand with the internal/covered hoses reading '95). I knew it would need the cylinders either rebuilt...
  7. D

    Bobcat 763 Loader Arm Question

    My 763 has a door on the front of the cab and the loader arm is up just enough to prevent opening of the door (long story how it got this way). I tried disconnecting the hydraulic lines to the loader arm cylinder to no avail. Any ideas on how to get the loader arm to relax? I haven't yet...
  8. Iftisam Mulani

    Suggest me a website with....

    Hi, Need help with high-quality cylinder parts & seals, tried this website - www.fpeseals.com, can anyone suggest other websites in the UK to explore
  9. F

    Hydraulic cylinder repair, welded

    Hi, I'm new to hydraulic cylinder repair, and was wondering if I could have some advice on the cylinders I have and how to go about repairs. I bought a second hand loader recently and am making repairs as I fit it to my Massey 35. Photo one shows the cylinder. There's weld on both ends and the...
  10. S

    YFL 155 hydraulic cylinder replacements

    Good morning/afternoon! My saga with the YFL155 continues, although, I think I'm getting a better handle on it (with your all's help). I have a 155d yanmar with a YFL155 FEL. I identified that the lift cylinders have an internal leak (valve is fine). I know there's little known about the YFL155...
  11. S

    Westendorf TA25 cylinder rebuild

    Hello I have TA25 loader and am wanting to rebuild the cylinders. I am able to get the tilt/bucket rams out as they are held with a simple snap ring. However I can't figure out how to remove the lift cylinders. The end had a steel plate with two slots in it. I don't see a snap ring or how...
  12. S

    John Deere 520 Loader

    I have a John Deere 2150 with a 520 loader on it. I am looking for a replacement hydraulic cylinder for the bucket because the rod is bent. The rod is $540 and the assembly is about $575. Does anyone know of an aftermarket cylinder that will work for it? According to the research I’ve done...
  13. C

    Kubota 7040 uneven hydraulic cylindars on loader arm

    I have the same issue on my tractor as this older thread. I tried to shim the side that was closed but it had not effect. When the cylinders are in the full dump position the right side is extended about 2 inches farther than the left side. do I remove the upper hydraulic line and pull it...
Top