ford 6640

cannot get clutches to calibrate error 24

So im looking for some help on a Ford 6640 SLE 16x16 powershift transmission. The background on the tractor is it was one of those auction buys that was too good to pass up and now i know why. It has an Alamo boom mower on it in great shape and i figured it would be very handy to have around the...

Hoping someone can help me out here. I have a 1993 Ford 6640 SLE with the 16 x 16 Transmission. Seems like every time I get ready to use it i get the E24 Code and have to calibrate the clutch spring pressure. Once I do this it runs great all day and the next morning I have to calibrate again. I...

Hoping someone can help me out here. I have a 1994 Ford 6640 that will idle fine but when I give it throttle it will start missing and making a popping noise from the exhaust. Smokes quite a lot too. White smoke and Black. So far I have had all the injectors tested and all were fine. Changed...

Looking for some help on the Hydraulics on a Ford 6640 SLE. I have checked the Hydraulic pressure and everything is good. This is the Model Tractor with 3 hydraulic filters. These have all been replaced along with new hydraulic oil. Still nothing. Arms will not raise. Is there anything...

I am new to this site and am hoping to gather some information on my tractor. Just purchased a 1993 Ford 6640 SLE at auction for $4200. Tractor only has 2800 hrs. and looks like new but tractor was inoperable when I bought it due to transmission problems. Got it home and changed all fluids...

Hey everybody!!

I am having problems with my 6640 - replaced the batteries and worked great for a few hours Replaced the PTO switch and think I have the wires mixed up. Does anyone know or have the schematic with the wiring diagram for the PTO assembly switch?? Any suggestions would be great!

I have a 6640S Ford with a 12 speed F and 4 R manual transmission. Last year the clutch was frozen and could no be put into gear. After some manual ministrations (in gear and pushing/pulling with the clutch pedal pressed) the clutch released. The tractor ran all season last year and never...

Hi Has anybody got the torque settings for the engine of a Ford 6640 available?

I have a Ford 6640 four wheel drive tractor that the PTO stopped working. It seems the switch works, and the module tested bad so I replaced it. It still won't come on. I have the large three ring binders, but I do not find in them where the solenoid is. Does anyone know where that is located?

hi, i need electrical schematic to ford 6640. i have a problem with charging and the unit of Dashboard. maybe i have more problem that i dont found than i must the electrical schematic to check it. Thanks, Cahani.

hi, i need electrical schematic to ford 6640. i have a problem with charging and the unit of Dashboard. maybe i have more problem that i dont found than i must the electrical schematic to check it. Thanks, Cahani.

Hi, i need service manual or shop manual for ford 6640. thanks, cahani.

This is a 1992 model with a cab and MFD. It has a gas tank in front of the radiator and one under the drivers side of the cab. What i have done so far is shut the needle valve going into the top of the sediment bowl; disassembled and cleaned the sediment bowl and reassembled; i have removed...

Looking for some advice on my Ford 6640. Everytime I engage the PTO switch, it works for a second and the blows the fuse. We tried replacing the switch and this did not work. We have check most of the wiring pretty good but cannot find a the short. Any suggestions on any other areas that we...

My 3 point hitch on my Ford 6640 is stuck in the up position. I am not sure how to release the pressure and get it down.

I'm needing some help. I just bought a 1992 Ford 6640 and it won't go into any gear. Well, it seems to be able to be placed in different gears but no matter which one it's in, it won't move. It's flashing an E code (E-24) so I'm guessing that's what the problem is. Has anyone experienced...

Anyone have any Ideas my 1991 6640SL won't lift its 3pt hitch it doesn't move at all. Was working fine then when I went to use it nothing. But all my live hydraulics pto power steering front load ect all work fine anyone have any ideas