Hi and again, thanks in advance,
The three point lifts and operates almost as should, but as soon as I turn the tractor off, the three point lowers to the ground with the lever in the up position. There's a trim mower on the back at the moment and it never did this. I'm thinking there might be...
Hi and thanks in advance,
I'm in the market for a used bush hog for a Ford 1220 and was wondering if there is a preferable size for this tractor. I'll be cutting about 23 acres of pasture.
Thanks!
A few weeks a go, my radiator fan was shattered from what I believe to have been a stick that got up there. These are cheap yet, difficult to replace as you have to take the radiator out, things are tight and have to be done in a specific sequence. Completed the replacement of the fan...
Hello All,
Please accept my thanks in advance.
I'm working on a Ford 1220 and found a leak in the hydraulics. It's a "step-down" on what I believe is the return line from the power steering back into the hydraulic compartment under the seat. The tractor was gushing hydraulic fluid and when I...
I have my tractor split for repairs. It has 1500hrs. Replaced bad clutch, center shaft in clutch disk was loose and springs were
rattling around. TO bearing was near perfect, replacing anyway. That explains some weird noises while engaging/disengaging clutch.
I hear faint gearbox noise...
I bought a very used Ford 1220 from a local landscape company. It has an unknown brand FEL. It is connected to the Hydraulic Manifold block at the inlet and outlet ports. The control screw is set in the Lift Linkage position. The FEL works but when I lift with it the lift arms drop. As soon...
After looking for literally years to find them I finally got a set of turf tires to fit my tractor. The tire sizes are correct front being 20x8.00-10 front and 29x12 -15 rear. The rears fit perfectly and the front bolted right up but would not turn. It turned out the inside of the rim was...
Hi everyone , hope someone can help me , I have a Ford 1220 HST and over the last year the problem has got worse , the tractor won’t move forwards unless you have almost max revs on , the lift is also jumpy , I’ve replaced all hydraulic filters that I know on both screw ons underneath tractor to...
so I've got this ford 1220. It has 2100 and some change on the meter, Hydrostat transmission, FWA, rear and mid PTO. It's had a rear transmission half put in it. I was using it to carry some gravel on the three point and it started making a terrible noise underneath. It sounded like gears...
I have a Ford 1210 with a 768A loader. The engine on the 1210 needs to be rebuilt. I have located a Ford 1220 nearby without a loader that is for sale with a price less that the cost of rebuilding my old tractor. I want to know if I can put my loader on the 1220 tractor.
I just upgraded to a newer New Holland. Looking to sell my current 1992 Ford 1220 that I love. Had it for a while and I'm not really sure what to ask for it. 2500 hours on the 3 cyl diesel, previous owner said the engine was rebuilt, it runs like it was but I don't have any paperwork...
Hello, I'm a new owner of a ford 1220 4x4 1988 tractor and I'm having issues with the ignition switch and by the way is $160 at the dealer. can someone tell me if I can replaced it with an aftermarket switch?
thank you.
Want to trade AG tires and rims for Turf tires and rims on my Ford 1220. Two front tires are new one rear tire is bad but still serviceable will trade up or down depending what you have. Thanks for looking. Bill B 48O 239 5537 Cave Creek AZ.
Ford 1220, it sat for a few months. When I went to start it, it turned slowly, then nothing, dash lights on but dim. Battery was old and low, replaced it. Cleaned battery terminals and and connection to ground and starter.
When I turned the key with the new battery, I heard one loud click (like...
I have a Ford 1220 and the temperature light does not come on. The bulb is fine, and it will come on if I ground the wire. I'm thinking maybe it is the sender unit? Does anyone know the part number and/or where to get a replacement? I can find them for models 2000 and above, but nothing for the...
I am having a problem to figure out how to tie into my tractor hydraulics to have rear hydraulic QC to run my backhoe I have a ford FEL and valve now that has 3 lines going to it there is also another line out of the hydraulic block just below my pump which is feeding the FEL on the lower left...
well, after 24 years, the bearing in the waterpump finally failed...
the thermostat is in the waterpump housing, and cant be changed without removing the waterpump...
one thing I noticed, is there was no rubber gasket under the thermostat...I got one at the dealer, but not sure im going to use...
Hello. First time poster on here. I have a little Ford 1220 4x4 w/ loader. It will start up fine the first time and run for as long as you want but when you shut it off, it doesn't start again until it sits for a long time. Where should I start? Any help is much appreciated.
I am looking for a CUT/SCUT. I found a local guy with a Ford 1220, MFWD, loader, 3pt blower, tire chains and about 700hrs for $5000. I would have to get a MMM separately (see them anywhere from $800 to $2000).
However I just found a Simplicity Legacy with about the same hours, MFWD, loader...
I have not posted since 10 years ago when I was thinfing about a Chinese tractor. I will make up for it with this post
12 years ago I bought a used '91 Ford 1220 from an estate. It was smaller then what I wanted to replace my MF 135 but with 300 hours, it was pristine and the price was right...
I have a ford 1220 that has served me well. Lately the front end is clicking and grinding when 4wd is engaged. If I hook up to something and try to tow it it just clicks wont move it.
Anyway I assume I am in for some front end work. Can anyone tell me where to start? What wears out?
I would...
Both my safety switches are bad, they've been going out since I bought the thing about 10 years ago.
I can't seem to find a replacement or a part number for that matter. I thought about bypassing them, but they're there for a reason.
Can someone point me in the right direction to find these?
Hi all...I am new to the forum and new to tractors...I have a lead on two units...one old, one new:
Ford 1220 - 1989 (serial #)
- $7800
- Shibaura engine
- Power Steering
- Loader
- Mower with shoot/bagging
- Tractor Supply quality rear blade and boom pole
- Less than 1000 hours (seem too low...
Hello all,
I posted here a couple of days ago looking for advice on tires for my 1220.
Apparently I'm learning the hard way how difficult it is to size up tires (R1's and R4's) for this thing without swapping out the rims.
And I understand how important it is to maintain geometry/dimensions of...
Hello,
I just picked up a Ford 1220 4X4 and it has turf tires on it. When I asked the dealer to find me a set of AG's or R4's for it and he told me it is nearly impossible to fit those types of tires on this tractor due to it's "odd" size rim. He also explained how crucial it is to properly size...
Hi,
I am going to look at a hydro,4wd diesel 1220 w/FEL and Backhoe, 3pt and pto with 2500 hours, they are asking $8000.
Anyone have experience with this model and know if their are specific things I should look for? Any issues in general? Is 2500 hours a lot for this tractor?
I am a first...
Just bought this tractor and it has a whining noise coming from the bellhousing area.when I depress the clutch the noise is still there as long as the tractor is moving.It will stop if the machine is stopped.I have pretty much ruled out the throw out and am leaning towards the pilot bearing but...
I am looking for some insight on a front snow plow for a 1220 Ford diesel tractor. My friend has a 1220 and is planning to get a 3720 JD for loader and backhoe work. He is going to keep his 1220 for snow removal duty but would like to mount a front plow. Any data from anyone about where he...
hey guys im new to this...a friend of my dad's brought me this ford 1220 with some issue's and i could use some help...they left the fuel cap over the winter and then ran it like that...replaced injector's still has a miss to it..thinking they might have smoked the injector pump. 2nd issue is it...
I just got a Ford 1220 4wd tractor and was considering chains for the front end - however it does not look as if there is enough clearance between the tires and steering linkage etc. My neighbor solved the problem on his Kubota by reversing his rims - the extra offset to the outside gave him...
Can anyone tell me if the bolt pattern for a Ford 1220 (best guess) will match up to a MT 372?
There is a set of AG tires/rims here that I'm looking at:
FORD TRACTOR TIRES - Cape Breton Farming Equipment For Sale - Kijiji Cape Breton
Thanks,
I have a ford 1220 tractor. I cant find out what catagory hitch it has. I am considering a 3pt log splitter from Tractor Supply. I spoke to the sales guy and he said it would work. I also went to my local new holland who also had a model tha the said would work as well. Neither seemed like they...
I have a ford 1220 and am considering purchasing a 3pt log splitter fron tractor supply. First of all anyone know if a 1220 has the power to do this? The ad says it is for a cat 1 or 2 tractor. I dont know what cat tactor mine is. (that could be a show stopper)
I went to my local New Holland...
I am looking at buying this machine, it currently is not running. being a hydrostatic drive, does it have a neutral position in the transmission or do you have to loosen a hydraulic by pass valve to safely move it with out damaging the drive mechanism? thanks for any help
I have a 1992 Ford 1220 HST. I was blowing snow and the wheels were spinning on ice when it quit spinning and no forward or reverse after that. I have a shop manual that said it may be a plugged hydraulic filter, So I changed the filters and fluid( semi-synthetic fluid). Still nothing! Checked...
Hello group,
I have a Ford 1220 compact tractor. I am relatively new to this machine, having only owned a lawn tractors before this.
I want to buy a 715a snowblower for the front. I found one at a tractor dealer in Iowa. I was hoping to get a head start on getting the tractor ready to run this...
Could anyone give me some idea what this Ford 1220 tractor would be valued at today? This 1220 comes with turf tires, a five foot belly mower, its hydro drive, has a rear blade and a front power angle up/down blade. This 1220 runs and starts very well. I just need some help to figure out its...
I feel a little stupid posting this....but. I have a question for anyone with knowledge of the OEM Ford loader valve. I purchased one off ebay for a loader I was fabricating for a mitsubishi tractor. The valve was made for the 1200 series and I am hoping someone can help me figure out the port...
i have a ford 1220 that has been recently rebuilt. it starts and runs fine but when run for a while it is hard to start. injector pump and injectors were rebuilt. any ideas would be appreciated thanks...
i have a ford 1220 3 cyl. diesel, i had a friend rebuild it and it starts and runs fine but when it gets hot it is hard to start.injector pump and injectors were rebiult. does anyone have any ideas. thanks
Help! I am attempting to switch from turf to Ag tires on my '93 Ford 1220 4x4 but cannot find wheels for less then $900. My efforts on the net have not yielded any better results. Any info to help locate reasonable priced wheels would be appreciated.
Help! I am attempting to switch from turf to agriculture tires/wheels on my Ford 1220 4x4 but cannot find the wheels for less then $900 from the dealer. My efforts on the "net" have not yielded any better results. Sizes are:
6-12 (front) and 9.5-16 (rear). Any help locating more reasonable...
There is a good sized equipment auction coming up here on Saturday. I jsut happened to be passing the fairgrounds and saw some of the stuff set out in preparation, so stopped in to see what was there. There is a very nice Ford 1220 with 550 hours and a MMM. Anyone with some idea what it's worth?
Hey all,
I just registered today, but I own a Ford 1220 4wd tractor. It is a 3cy. Diesel.
I have a 5 ft finish mower and a 5 ft blade that came with it.
I am mowing 3 1/2 - 4 acres of uneven ruff ground. I just bought the land a year ago and have not whipped it into great shape yet.
I am in...
I bought a Ford 1220 at a auction. It had 1400 hours on it. First thing I did (except for driving on and off the trailer when I bought it). Was park it in my garage and saw no oil on the floor under the tractor. Before I mowed for the first time. I change all the fluids and filters. I used...
I recently purchassed a 91 1220 and am looking to get a belly mower for it. I am looking for recomendations on brand, ease of mounting and removal, and of course value.
Thanks much
Could anyone give me some leads to "tractor wreckers " I have a 1989 Ford 1220 and I'm looking for a mid mount PTO assembly. They quoted me a pretty incredible price at the dealership here in Saskatchewan so I thought I might try looking around for a used one. Thanks okiedokie
Hello,
I just bought a '89 model Ford 1220. Nice tractor but I never got a mid mount PTO with it. Anyone know where I might find one. Dealer up here ( Sask ) can order all the parts to make one up but not the unit as one piece. As you can guess the price gets a bit much this way. If anyone...
I recently bought a ford 1220 tractor and I am interested in getting a front end loader for it. Anyone know what type of loaders will fit this model. Also places that might sell used attachments for it?
Hi, you guys I jus thought i would tell you that i finially traded my John Deere 318 in on 1993 Ford 1220 4wd with manual steering and a 60" mid mower. The tractor has 1040 hrs on it and has no scratches or dents on anything. I am going to pick it up today, so i will tell you more later on and...
Well as of a couple days ago I again feel like a legitiment member of the tractor community. I purchased a 1994 Ford 1220 (HST, 7106 loader, backhoe (I haven't figured out the model yet), power steering, ag tires 438 hrs) Someone is bound to ask, I paid $8800. Some of you may have seen it on...
Hi, Where could I buy an early 1990's Ford 1220 in nice condition with mower deck (maybe loader also)? I don't care about the hours. I live in the NorthEast but can travel for a good deal. My limit would be 1,200 miles. Any help? Thanks