broken

I was replacing the Rocker Cover Gasket MIU11358, and when I put the cover back on (left side with the oil fill), I noticed a wire broken. It is a yellow wire with an L shaped connector (Yellow Box). I believe it was attached to the connector (Blue circle). What part do I need and how do I...

Why does JD put the key where they do? Keys are dime a dozen, but when you can not get the broken key out it becomes an issue. When you forget it just once, snap!!! No more for me. !!!!! I ended up not being able to get one out so I got an aftermarket switch. Didn't even check OEM price! I...

I bought 12 acres just up the road and uphill from my 25 when a month of rain convinced me that putting a house where I originally wanted to would be a continuous and expensive drainage battle. One issue I have is that there is broken glass all over the area around the pole barn and where the...

Today the front end of my ym186D had what i would consider a catastrophic failure. I had it in 4x4 and it made a noise and i think i have something broken in the front end. I parked her and removed the front driveshaft to find that if i try to move the tractor the front axle will turn about...

I'm sad, The left side brake on the e27n has always been "grabby", and since it's such a nice summer day I thought I would dig into it and see what might be a miss. Turns out the main pivot stud is broken off at the mounting stud threads. I just got it all apart and half cleaned up. The...

My Sawsquatch slipped off a higher cabinet and hit my air compressor. I can only assume the shipping container was jostled enough for it to slide off. This could have been from storms this spring. Could have been a possible earth tremor too. Anyway, No damage to saw but a piece of compressor...

I have a Case IH DCX101 that I just purchased in the spring. I used it for the first time this past weekend and when I would engage the PTO the discbine would shake pretty hard until it got going. Yesterday when I engaged it (I started at low rpm) it actually stalled the tractor. It did this...

Not sure exactly how it happened but I slammed the front loader bucket into a embedded rock and somehow something went into the bottom of the radiator and holed it. So now I need a replacement (Does not seems to be any radiator repair shops around that I can find.) Does anyone have a source for...

Hi all, I have the opportunity to buy a 2019 3650 HST Cab model. It has only 3h on it, and is described with "needing HST". It seems to me that the transmission would have to have been broken from the factory at those hours. Its 3h away, so I wanted to get some of your expert opinion here to...

Looking at a Yanmar YM330D with 1600 hours. 4wd doesn't work and current owner bought it that way and doesn't have any info. Im new to tractors but not to mechanical work. Question is how hard/expensive would it be to fix the 4wd? Asking price for the unit is $6000. I know Im not giving much...

I am the somewhat fortunate recipient of a free tractor. My dad purchased some land in coastal North Carolina and on that land was left a tractor that at the time was non-running. He dragged it out spent a couple thousand dollars on it and decided it wasn't big enough for his needs so he dropped...

Hey everybody! I just picked up a 5234D with a broken driveshaft and input shaft on the hydraulic pump. I've been trying to find a replacement pump but haven't been able to find anything. I have found input shafts for this unit, but have been advised against attempting the repair as "It's more...

My 2nd time out after the unit was returned from the dealer following a rebuild of the hydraulic system (new valves and pump all warranty work). I was using the front loader to scoop wood chips and lost pressure on my bucket curl. Could hear a hiss when trying to adjust curl and immediately...

Just wanted to post an issue I had with my CB85 backhoe from Massey Ferguson, and get some thoughts on where to go with it. And maybe help someone else who might find themselves with a cracked hoe. This backhoe has something like 100 hours on it. Bought it new with my tractor (MF 2850E) in July...

In case anyone takes life for granted when standing near a spinning PTO shaft - here's what can happen when a #8 grade bolt for PTO clutch is no match for PTO engagement at 2000 RPM's (that was my fault - had just turned PTO off and saw I had missed a spot so turned it right back on before...