bobcat 763

Leaking hydraulic pressure sensor. Replaced x2 Now leaking again after only short usage.

My 763 has a door on the front of the cab and the loader arm is up just enough to prevent opening of the door (long story how it got this way). I tried disconnecting the hydraulic lines to the loader arm cylinder to no avail. Any ideas on how to get the loader arm to relax? I haven't yet...

I've been in the process of converting my 3pth snow blower to hydraulic so I can run it on the Bobcat. I got the pump mounted on the blower with direct drive and put the blower in the SS snow bucket to see if it would work. It did but not well. So I did some checking and I think I have a...

I posted this in the Bobcat forum as well but thought I would try here as well since this is Hydraulic specific. A month ago I purchased a "new to me" bobcat 763F. It has 2500 hours on it. About a week ago the machine stayed outside over night and the temp got down to 15*F when I came out in the...

I have a slow drift down of my lift arms, not a serious leak yet. But, I noticed when i leave my sand bucket on it's "cutting" edge over night the front tires will have lifted off the ground. I would guess the two "problems" are caused by the same failed/failing part. Does this point to one...

Got a small hairline fracture in the housing on the radiator on my 763. Its small enough all it does is fizzle when it gets hot. Is JB Weld something good for this or would you guys just take it out and repair it? I normally do stuff right and not patch it, but I've got to use it this upcoming...

Hi guys, I have an Bobcat 763 with a a weird problem. I'd appreciate any help. Last winter, after the weather got down to 8 F here, I came into the shelter to find my B/C 763 had dumpled enormous amounts of hdro fluid onto the floor. The machine was running fine up until then. I'm not that...

I'm looking for a free copy of the bobcat 763 high flow rapair manual, in a digital version. I just need to check an electric system recently repair i made. Thanks a lot g

Iｴve recently bought an Used bobcat 763 high flow (turbo), and iｴm working on for rebuild its electric system, that looks not so bad, but needs reconnect some cut wires somebody did cut. To do this, i looked for someone who could know and could do this, but, it results impossible. Well, i...

Recently started working on a 763C with the Kubota engine. The unit has been sitting for several years, but initially cranked as it always had. After adding fuel, we can not get any fuel to the primer bulb, nor will it flow with the bulb removed. Is there a solenoid or check valve on the fuel...

I,m looking at buying a 1999 Bobcat 763. I've checked it out and all seems great except that it has some blowby. The down pipe from the valve cover breather is not connected to the breather and I could see some oil below the breather. So I put my finger over the open end of the vent and could...

I've been looking at used skid steers for a few weeks and a couple have found a couple in the right price range. Since I know nothing about SS's I thought I would ask for advice here. The 2 in question are both manufactured in 1999. The New Holland has 2700hrs on it and comes with an enclosed...

Noticed that the tensioner spring was no longer keeping tension on my cooling fan belt. The spring and arm will only move when i physically pull on the idler pulley to increase tension on the belt. Because the spring and arm are not moving freely it allows me to keep tension on the fan belt. I...

Our bobcat worked fine and we rented a bobcat auger attachment. We connected it and drove it to where we were going to work and then went in for dinner. We came out and it wouldn't start. The panel lights started flashing when you turned the key. The error code is 0314 low voltage. We...

This has happened twice now I was using my machine in the dirt fixing a culvert working all day fine towards the end of the day it pull's a code ACH 31-32 it will let you raise the arm, but when you go to tilt the bucket the code pops up. I lifted the cab and switched the plugs on the Actuator...

This has happened twice now I was using my machine in the dirt fixing a culvert working all day fine towards the end of the day it pull's a code ACH 31-32 it will let you raise the arm, but when you go to tilt the bucket the code pops up. I lifted the cab and switched the plugs on the Actuator...

HOPEFULLYAD SOMEONE OUT THERE CAN HELP. I WAS DOING SOME DIGGING TONIGHT AND AFTER 15 MIINS I HAD A LOT OF STEAM COMING OUT OF RAD CAP IT LOOKED LIKE. I SHUT IT DOWN AFTER SEVERAL MINUTES. IT WAS GURGLING BAD. ANTIFREEZE SHOT ALL OVER THE PLACE INCLUDING MYSELF. I COULDNT TELL IF IT CAM OUT...

I have got a, new to me, bobcat 763. I just got it running and noticed that the air cleaner 'can' is pressurized. That is, since the cover has been dented, I can feel a little air blow out of it when the machine is running. When I turn off the machine, there is a big burp of air ( not a backfire...

Hi, this could be a reoccurring problem even though I do not find remedy in the repair manual. I have an old 763 hi flow with 6000 hours. After starting all works for a while then the hydraulic oil starts leaking out from a hole in the left side lateral drive engine into the oil pan. Could...

I have a 98 763 that I've been ignoring a leak and I'm tired of spreadng kitty litter. The machine has 3400 hours, mechanically runs strong and asthetically looks real good. What are common leaking areas with these machines?

lately the unit starting to move by itself - levers are in center postions - cannot stop unit- have to keep moving levers back and forth to stay in position !!

I bought a 1999 Bobcat 763 skid steer. It didn't have any manuals with it. Would any one care to "share" their service manual with me? Thanks, Harry

Hi, This is my first question. I just bought a used Bobcat 763. The instrument/gauge panel in the upper right corner is very dim. Can barely see it. I believe it is lit up in an orange color, showing the fuel gauge, etc. Anyway, is there a way to make it brighter? Is there a "rheostat" like a...

My bobcat will not turn on, had three codes 21-02, 02-16 and 08-21 change my ignition switch. Now only two codes appear 02-16 and 08-21 but bobcat still wont start

i have bobcat error codes 21-02, 02-16 and 08-21 can someone help