asv rc100

I just bought a used RC100 with an unknown amount of hours as the display seems inoperative. But that isn't my issue. When cold the RC100 acts mostly as it should although turning is jerky and fast sometimes and slow others. However, when warmed up you pretty much have to stop moving to turn...

Hello everyone. I have an ASV RC100, first CTL I have owned. Question for anyone else out there with an ASV CTL, when using a grapple attachment, do the jaws slam open or shut when you activate the thumb switch on the right joystick, or is it more gradual? On my machine the switch seems to only...

I know this is a very common problem with these machines. Over time my overheating issue has became more and more common. I've fought this issue for some time now. I can assure you this has nothing to do with any attachment. My problem persist and I just do bucket work. If anyone has any new...

My skid steer has developed a problem with the ( float position) when I go to back drag with the bucket. I have cleaned all of the connections so I am assuming their must be a by pass valve that. Is not working? Any direction on how to fix the problem would be appreciated..

2005 ASV RC100 Track Skidsteer Perkins 100 horse engine. hydraulic over hydraulic controls. engine sounds good. operates with no hesitating or jerking. all smooth. no loss of power from engine or any hydraulic use. at idle everything runs quiet. increasing the rpms a little starts the...

HI FRIENDS. PLEASE HELP ME ON MY RC100. I BOUGHT THIS MACHINE BUT IT HAD THE COOLING TEMPERATURE SENDER AND THE OIL PRESSURE SENDER BROKKEN ALSO THE INJECTION PUMP WIRE WAS DISCONECTED. NEED TO FIND WICH WIRE GOES TO EACH OF THIS PLUGS. AND WHERE THE INJECTION PINK WIRE IS SUPOSED TO GO. ORDER...

Hi there, I have a ASV Rc100, that is stuck in hi speed, I'm running out of things to check and replace. so far I have done the following. Replaced both Drive motors, checked hi/low speed solenoid & shaft, replaced all hydraulic filters, replaced all seals in hand controller. checked all...

I recently purchased an RC-100 (pre-Terex model) overall in great shape. Before really putting it to work, I'm going through the machine and giving it a thorough once-over. I got all the ASV tech bulletins that apply to the machine and am making sure those items are up to date, and undoing...

My RC100 skidsteer died deep in the woods with hydraulic drive motor issues, could not be repaired in field. Constructed a sled with timbers & steel then used CAT excavator to drag half mile for repair. Lifted rear of machine and pushed sled underneath. Tracks don't free wheel, they are unlocked...

I have an ASV RC100..... The oil pressure and charging system idiot lights don't work... I assume they should come on with the key on and engine off.... The only time the charging system light comes on is for a split second when the key is turned on or off.... The alternator is new and it's...

My right track is has little to no power, left side also seems weaker than it should be. It seems to have started when I shifted from 2nd/high to 1st/low speed. Left joystick? The right drive motor is near new with new filters / fluid. Any Ideas??

The AC condenser on top, I took mine off flipped it upside Down behind cab. So far much better, less rain water and trash From mulcher, the fans took them oem off put two 12" from Auto store on it. Cost much less, working good.

having problems with Turtle mode going to Rabbit mode. How do I fix. I have a 2007 ASV RC 100

I have a 2007 RC100. I have a problem. I'm having problems with turtle mode going into the Rabbit mode. I think a switch is going out. Anyone had this problem. I you think it is the switch, what is the part number and where can I get it.

After reading about all the issues with the bobcat mulcher heads and I don't see buying a brand new $100k machine to start off as a smart business decision. I've been looking at used machines and found what I think is a good deal on a low hour RC100. 2004 ASV RC100 600hrs on machine Less than...

I am having a problem with 2007 asv rc 100 . it will not start. the fuel pump comes on and some of the relays are energized but no starter. I can jump the starter relay and it turns over but I need a wiring diagram to really find and fix the problem. thanks

It's about time for me to replace my tracks and I'm looking for advice. I got about 1600 hours out of the original set of tracks and they need to be replaced because the rubber has chunked off to the point where the outside most wheels are exposed on both the outside and inside edge of the...

Has anyone had experience changing this part out themselves? I ordered the resolver block but it came as two bags of parts, some of which make no sense to be included and obvious parts that should be included are not included. Quite annoyed to spend $450 on a bag of parts. I was under the...

I'm thinking about getting a skid steer of some sort for home use. I'm not a contractor, I'm just going to use it around 100 acres of property for working on my trails, making new ones, getting firewood, snow removal, ect. I might average 150 - 200 hours a year on it. I definitely want tracks...

My asv rc100 won't shut down after key is in the off position. I have replaced the fuel filter along with the fuel shut off soleiond. It starts up every time and run like a top at any rpm. It's hard to believe it's the fuel injector pump when it runs the way it does. Just wondering if anyone has...

I have a 2007 asv rc100. It will crank and run for and then shut down after 5 minutes. Any one have any ideas? we replaced the lift pump and filters, bleed the line and still have this issue?

LIFT ARMS WORK PROPERLY WHEN HIGH FLOW AUX IS NOT ENGAGED. WHEN I ENGAGE HIGH FLOW TO MY CUTTER, THE LIFT ARMS WILL NOT GO UP OR DOWN ; HOWEVER THE BUCKET TILT WORKS FINE WHILE CUTTER IS ENGAGED .JUST NO UP OR DOWN WITH ARMS... ANY SOLUTIONS ? HELP WOULD BE GREATLY APPRECIATED !

I am rebuilding the right side of the machine after a bearing failure. I am cutting no corners due to the money spent on doing this. I have all the parts to rebuild but i have one question, and that is do i pack the bearings with grease or does the axle tube get oil put in it through the hex...

Looking at an 2006 ASV RC 100 for $26500 and a 2008 New Holland C185 for $28500...both have appox. 1200 hours...and the new holland has brand new tracks. Would be used mostly for ranch work...moving large round bales, grubbing small mesquite trees, pushing and raking brush, and digging post...

Our RC100 is slow to respond when turning left. Line pressures seem proper, and engine RPM makes no apparent difference. Once left turn engages the unit runs true. Makes no difference whether forward or reverse the slowness of initiating left turn is same. I believe problem is a sticky shuttle...

Our ASV RC100 is slow to respond when turning left. Once turned stability is good. Engine RPM makes no difference

Do all ASV RC100 skid steers have highflow hydraulics on the machine? What are pilot controls?

Myself and many others on here have had issues with failing seals and bearing failures in bogie and idler axle assemblies. The first few that went out on me I ended up buying new ones at $450 for the bogie axles and close to $600 for the 14" idler axles. My dealer said they don't rebuild them...

I am in the market for a set of new tracks for an rc100. I have got a few quotes so far DRB Aggressive tread $1475 ea on close out no warranty. camo plast $1950 each Also got a price from tracks-undercarraige.com $2060 each for OEM and $1625 each for DRB tracks that have a very similar pattern...

Hello. I really need some help with this. I bought the machine about 2 years ago. A 2006 model RC100. It came with a loftness G1 carbide cutter that I was told needed new teeth. Before buying th machine I had talked to a service tech at my local dealer and he told me if I bought one (rc100)...

I have a ASV RC 100, with a FAE Head on it. I works 10 min. with the head and it hard go left, right or forward. It will also not go up on trailer unless it cools down 30 min. to an hour. Then it will go on trailer. Changed 3 different oils, need help? Thx the head works all the time

I don't have an over flow on my machine and I loose some coolant each time I run the machine. I did a pressure test and it doesn't leak so I am assuming when the coolant expands it goes out of the overflow tube. I guess this means it is an open cooling system. Has anyone ever added an over...

Hello all. I want to take the radiator out of my rc100 for repairs. On the hydraulic side I want to buy some caps and plugs for the lines so I wont have to drain out my whole hydraulic system. Does anyone know what size these plugs and caps would need to be? Thanks.

I have a 2005 asv with a heater and air conditioning unit that do not work. I have cleaned the coils on the air conditioning unit and still no heat or air. I also have a Bobcat 331 excavator and the same problem with it was solved by replacing the mixing valve under the seat. Has anyone an...

Was cleaning out the tracks on my RC100 cleaning it up to do a service on the machine. Moved it around the yard a few times from the shop to the wash bay and back, etc... When I got in it after pressure washing the tracks the machine cranked up fine but the loader arms are dead. No hyd...

I was talking to a fellow mulcher yesterday and he asked me what temp I was running while working. I told him 220 and he was like WOW! I have been using the machine for about 250 hrs and it has always ran that high. I have good and full coolant, and I don't see anything stuck in the radiator...

I was mulching yesterday and started hearing a wierd noise. It sounded kind of like the last time one of my bearings went out. I couldn't see anything wrong when I inspected. So I worked a little more. Then when I would turn I would hear a popping noise like the lugs were jumping on the...

Hello. I just purchased a 12000 lb hydraulic winch to install on my rc100. Does anyone know where the best place to hook into the hydraulic system will be? I saw a thread on here in the past and someone said they installed one, but I can't find it now. Any help would be appreciated! Thanks...

I'm new to this site, just joined tonight but I've been reading the post for sometime. I'm wanting to expand the services I offer and am considering a RC100 with a brush cutter and a mulching head. After reading some of the comments about problems some of y'all have with this machine and the...

I have a mulching job I am bidding on a creek that's a little tricky. It's .65 acres and about 100 ft wide straight down to a creek. There doesn't seem to be any severe drop offs but it is pretty steep going straight down hill. Everything I have been on so far has been pretty flat. Anyone...

Was running my machine just around the yard with the bucket on tonight. I had got out of the machine for a minute and when I got back in the machine would not move. I played around with the lap bar a bit and noticed that the turtle light for my speed wasn't on. So I decided to shut the machine...

I have a bobcat brand SG60 stump grinder that I want to use on a ASV RC100. The electrical connector is different. Does anyone know where I can buy the male end of the electrical quick attachment so I can rewire it to work on the ASV? Or does anyone make an adaptor?

I recently bought a 2006 ASV RC100. Only one of the front lights work on the front. I got to looking into it more and when I pulled out the other lights out the bulbs were not connected to the harness plug. There are 2 prongs that plug into a plastic/ceramic looking piece/plug. They will not...

I need a copy of the owners manual... I think 2006 model. Any ideas?

I have an unusual problem. I have a bogged down RC100. I lowered the carbide cutter all the way to the ground, and got out through the front door. The RC100 sank a couple inches after I got out, but the cutter did not sink, and so the hydraulic arms got pushed up a little and now I can't open...

I have seen a few places offering aftermarket tracks for ASVs. Has anyone use a non-ASV set of tracks? I was quoted 4600 for a set, a little under 2000 less then the factory ASV tracks.

Im in the market for a used t300 or rc 100 with a fecon mulcher.any input or direction would be great.I have had a demo in both.They both have their advantages.

I've been reading all the posts about ASV equipment on this board and thought I should post about my experience. I've had an RC100 for a couple of years on our horse farm, and the machine is just about to hit 700 hours. I love what the machine can do, but that said, I wanted to relate my...

Thanks to all for the input. I closed the deal today for a new rc100 with forestry package and fecon head. The sales rep said I was getting a pressurized cab with this unit. He said he knew they were coming out with one but was not expecting it this soon. I will take possession by the first of...

I had the opportunity to operate both of these machines today. The RC100 was equiped with a Fecon Bullhog and the SR80 was equiped with a Loftness Carbide Cutter. I went into some detail on comparing the two mulching heads in another post. I will attempt to share my observations regarding the...

I am going to have to replace at least two quick couplers on my ASV. Did manufactures ever get together to make these "universal", or does each brand still have it's own design? Basically, do I need to go back to ASV, or is there a chance my local parts guy could have them? They look like...

It has been interesting reading the different comments regarding different track loaders and mulching heads. I have been debating buying one for months now. I have ran the asv rc100 and the cat 287. I will demo the bobcat t300 in the morning. I believe the asv is the unit of choice by many. Any...

What brand mulcher attachment sould be best for a new RC100? Magnum, loftness, FAE, gyrotrac, others???