allis chalmers 5020

My first real tractor. :cool2: Allis Chalmers 5020 AKA Hinomoto e23 or Massy Furguson 210 or Simplicity 9523. mfwd with new rear tires, balasted, original loader, everything works well and well maintained. new alternator, nothing but a few small drips. should be delivered next week after the...

I mowed with it for about 3 months after i bought it and one day i rushed the glow plugs and flooded it. a few months later I got it to pull start and ran it for about 3 hrs and tried to key start it a few times after i shut it off and no fire. sence then I have put glow plugs, new fuel, new...

Hello to the Tractorbynet community! I have visited this site and decided to join. Our 1980 AC5020 is a rugged little tractor. So far I have been able to get parts without any difficulty through our local dealer. jrbalto

New to this. As I was mowing the tractor died. It acted like there was no fuel. I opened up the bleed valve, tried to start it and not fuel came through. Where is the fuel pump?

Bought a farm. Inherited an Allis-Chalmers 5020. I'm new to tractor/diesel. Help!

I am the new owner, and am going through repairing the hack jobs by the PO :mad:. Newest one is the charging system. It is a Hitachi alternator with three wires that connect. I am not getting any charging voltage. One is the BAT connection which traces fine to the starter and the battery...

Hi everyone, I bought an Iseki TU185F last year (it's a 4WD and - i think - 18.5hp). All the stickers on it are in Japanese and I don't have any manuals. So far it's been great but i wouldn't mind getting an operators manual and a workshop manual. Searching the internet it seems to be the same...

I broke the front drive line case on the right hand side of my Allis Chalmers 5020 MFWD tonight and am wondering where I can find replacement parts for this. Anyone have any idea? Thanks Bob Keller

I've been looking for a smaller used farm tractor and came across this AC model 5020. Does this look like a decent tractor for $3K? Are parts readily available for Allis Chalmers tractors? Thanks in advance, - djb

I need a water pump for my fathers' Allis Chalmers model 5020 4wd tractor. I have been told that this 2 cylinder tractor is really a rebadged hinomoto c-23 and the parts also fit a massey ferguson that was sold in the 70's as well. If this sounds correct where is the best place to look for a...

I have just inherited an AC 5020 4wd tractor. I don’t have the owner’s manual. I would like to service the tractor before I use it. What oil weight and type do I use in the engine and transmission? I also need to know filter numbers and suppliers. Any help would be appreciated. Thanks

23 hp. Not worried about tall grass, the idea is to keep it short with as few passes as possible. I can't find how much these weigh, I've found 6 ft flail mowers spec'd from 500# to over 1000#. I know I could do 500#, I just built a 450# driveway grader for it, picks it up no problem...

Do you have a parts catalog? Can you give me the part numbers for the bearings in the front end with 105 balls, the seals for those bearings, and the seals/bearings on top of the axle housing? I'm looking for those parts at salvage sites and they need the part numbers. Thanks, Monte

I found the source of my hard steering, the big thrust bearing with 105 balls is toast. I'm assuming both sides. So, I'm in the market for at least 2 of the 105 ball thrust bearings, seals, and the thrust bearings/seals at the top of the axle housing. I'll be Google'ing too, but I thought I'd...

Hello, and I hope this is the correct forum. Is anyone interested in a FREE 1981 AC 5020 (1/2) tractor? Well, less engine and front axle? Less than 600 hours. My salvage recycler guy has been eyeballing this thing for six months, and before I let it go, just thought I'd try one last time to...

I am looking at two small utility tractors with front end loaders. One is a MF 135, Gas for $4,500 the other is a AC 5020 diesel for $4,000. Condition is about equal. I have no experience with either brand. Looking for recommendations and advice on reliability and parts availability.