Search results

I installed a back-up lamp, intermittent wiper circuit board, switch for radio that bypasses the ignition switch, mud flaps, as well as the usual three mirrors, led work lights (front and rear).

I found mine fairly tight as well. I use anti-seize and so far haven’t had a problem.

You will love the Boss Plow - I've been using the VXT for 8 years now - fantastic design and function. I love the worksite tires and they give plenty of traction in most situations. I do put a set of chains on the rear tires when the road gets icy. I have been using basic H-style chains with...

I had a Boss v-plow on my X900 but did replace the factory front suspension with HD springs.

I have the Boss V-Plow on my X1100C and had one on my X900 prior to this. The hydraulics are responsive, lift height is wonderful and it is a breeze to put on and take off between storms - less than a minute to put on and take off! The front portion of the frame comes off easily in the spring...

On my 2022 X1100C there were wiring harnesses built in. Just need switches and the LED lamps. The wiring harness for the radio is there as well - a switched wire (red) and a white/green wire that is "hot" all the time. I plow two significant dirt road hills of over a mile with a Boss V-Plow...

I installed LED (two front and one rear) and then using the backup beeper wiring harness and hardware I installed a LED backup light. Works really well! Plenty of light for plowing at night.

I live in the Lakes Region of New Hampshire - we get an average of 75 inches per year - most storms are 4-10 inches. I have a Boss V-Plow. It is terrific.

I had a X900 for 7 years and 11,000 miles before getting a new X1100C this past December. I purchased a glass widow and metal roof for the 900 and I highly recommend going with a glass windshield with wiper if you are going to plow. Scrapping ice off a plastic windshield scratches it terribly...

I am on dirt roads, so once we have an ice storm I put them on for the rest of the winter. Two years ago I never had to put them on! The traction is really remarkable.

I encourage you to get a plow. I plow over a mile of hilly dirt roads to my home and although I have a F350 with a 9' plow, my go-to plow is my X1100c with a 6.6' Boss V-plow. I plowed with my X900 for 7 years and loved it so much (11,000 miles) I sold it to purchase the X1100C that has heat...

I purchased the adapter (aftermarket from E-Bay) and it works really well - doesn't change the geometry much and now I run my 18v tools with my 20v Li ion batteries. The tools work really well on the 20v and I've had the adapter for over a year and plenty of use. Certainly beat purchasing new...

I am not familiar with the early models, but my guess is that the heater may be an aftermarket unit? Check to see if there is power at the switch (assuming you checked the fuse). Good luck.

I added the adjustable hand throttle on my X900 after I tried plowing up some steep inclines on my 1.5 mile driveway. I know that the owner's manual says to not drive with it on, but with other equipment the hand throttle allows you to keep the engine rpm's up for just that purpose. It made a...

On my X900, and now my X1100C, I built a bulkhead and side extensions that work really well. If I hauled a lot of loose materials frequently I would add a firm rubber flap to the top of the bulkhead extension that seals off the gap between the bottom of the rear window and the bulkhead.

The Worksite tires on my RTV X900 were wonderful and lasted 10,000 miles. I plowed with them and I was always amazed at the traction. I replaced them with Sedona Coyote's and I love them also. I went with them instead of the worksite because I saved over 100 dollars and a friend had them and...

After three plowing seasons, the front bumper of my X900 snapped on one side and the other side is cracked. It is not a weld failure - the steel tubing sheared off. I had them welded by a pro as I don't trust my welding skills on such thin tubing and a crucial point. I plow almost two miles...

I just purchased a RTV-X900 and have made some modifications to make it into a maintenance vehicle for my work maintaining 47 structures on 110 acres with 12 structures built prior to 1900. I added an LED light up high in back to act as a back up light and to give light to the back where tools...

My throttle was very stiff when I took delivery of the tractor and I finally tore it apart and freed it up. After several years and 600 hours more it was becoming very stiff again. For those that have the same problem here are the steps that need to be done to free it up: The job only takes...

I am approaching the 800 hour mark and it is recommended that the valve gap be checked. I've done them on other machines but not on the B7800. Is it as simple as regular valve adjustment? It looks like the injectors are in the way and need to be removed prior to adjustment. Has anyone had...

Anyone have experience with a 4x2 or 4x4 Hart Cart? They look good on paper and the video, but I want some experienced feedback before I explore further.

I want to install a light in the dash (one of the empty spaces) which will warn us when the brakes have been set. One of the operators is somewhat disabled and doesn't have the leg strength to really set the brake. As a result he can easily run around with the brake on. Mechanically it is...