Search results

I'm going to build a hydraulic top link for my soon to be delivered 4155HC but since it is a Cat 2 instead of the Cat 1 I need the measurements. Fully retracted Fully expanded Pin dia. Thanks in advance for anyone that can help.

I returned from overseas two months ago to Colorado and the weather here as help make the decision for us that sooner rather than later was the time to get a new tractor. I ended up with using the same dealer in Penrose, Co. Randy took good care of me before when I has warranty issues (minor)...

I'm about to buy a John Deere 606 mower and I wondered in anyone had the tech specs on it. (deck thickness, weight, gear box HP) I'm unable to find a PDF that I don't have to pay $60 for but did find paper for $25 or more on Ebay & amazon. Technical Manual TM1394 Operator's Manual...

So those that have a hydraulic top link what are the length of your hoses? I'm about to order the top link and want to order the hoses and fittings at the same time. I do not wait till it gets here and measure with old air hose. I know there will be slight differences between suppliers but they...

So I've got over 140 hours on my XR4046HC and I was driving by the LS dealer and wanted to see how the new 3cyl turbo performed compared to my 4cly NA shibaura. I did a quick test drive and found that the turbo motor was a little rougher at lower RPMs but smoothed out with a few more RPM's At my...

I need to correct / modify a post that I created. http://www.tractorbynet.com/forums/ls-tractor-owning-operating/192544-ls-tractor-oil-gas-air-13.html#post3864237 2014 LS XR4046HC Engine Shibaura (Tier 4): N844L-F (Old) Oil filter NAPA # 1056 / WIX # 51056 (Improved) Oil filter NAPA # 1348 /...

Anyone know of a vender that sells QA tabs vs the whole QA plate. I'm going to be building a set of forks and it will be easier to just weld some tabs on the bottom of my lower square tube instead of adding more material by using a whole plate system welding on to the back of my fork frame. I...

I try to stay ahead of my service schedule, and during my 40h check I found my front axle bolts on the passenger side were severely loose. Three of Tue four on the passenger side were not even finger tight allowing the housing to start separating. I remove one at a time and used blue locktite...

Need to make some changes to a post I had made in the LS tractor section. I'm unable to edit and I see no way to report the thread so I can bring it to the attention of a moderator. I listed incorrect information in my post and need to correct it, so as not to confuse people...

Tractor XR4046HC Does anybody else have front tire rub on the FEL frame bracket (tube and plate)when fully articulated? Do you have issues pouring 5 gall fuel jugs into the tank......I think they should have angled the filler neck. Do any of your interior light switches light up with the...

Breaking in the new tractor today we got 4 hours on it. My first thought was that I was not impressed. As the speed was nothing like a PTO 3pt unit. I could not get a clean hole. So after the first hole I tried to do it different. I would run the hole a little bit deeper, turn off the auger...

So today I sealed the deal on a LS hat and Owner's manual since I had such a cute co driver they decided to include a XR4046HC and Danuser EP6 offset quick attach auger with a 12 bit. I want to thank Penrose Tractor Factory for the very soon transaction along with BSHfieldmaster (Rohn) for his...

It looks like most of you are running 6' blades and rakes or bigger, with some running a 66" or larger box blade. What is the going consensus for size on the 404x's. I know you typically want wider than your tire track but I only see the specs with Ag tires at 55.9" Anybody have the width with...

So I've decided on the R4047H, I'm still shopping for a dealer since none are anywhere near me. I would hope that a dealer checks in on this forum and give some info. Do I need to pull the trigger sooner than later due to the rumored Tier 3 going to a Tier 4? Does the dealer have any way to...