Search results

Here in Fl. just a little WD-40 from time to time.

B2630 and LX2610 463072,669929

12x12x12 Box full of sand.

I like the use of the Grill stand, and your tool lay out on the stand..

This is how it started..

Try this. it might help ya.

I had this on my B2630.

Lets try this one more time.

Well I hope this works. B2650[/ATTACH]

I hope we have no issues with this one..... Our 2005 B2630 Never let us down.. I need to come up with a price for this B2630 with the 60" mower...

This has worked Great the past few years for me..

Here is a better look.

This is my only stick welding, it a wind chim.

A better pict.

This might work for ya..

Works great...

Two more..

It works...

It's been slow, but I am getting there.

If you use the table a lot you will not see to much rust. I use WD-40 on my table top every 3 or 4 months. If you get splatter on it.... just use a flopeeee disc on it, just enough to remove the splatter.

This what I am trying to make..

The tines will be be these. on a 1 3/4 od pipe.

There is a thread that was started back in 12-14-2007 Good Landscape Rake Cheep. I am going to build another 3pt. hitch for it and here is the area I need some input on. I have a Kubota B2630 I would like to have the rake at least 12" or more from the back of the 3pt. so I can have a nice area...

I am trying to find some of these. I will be useing a pice of pipe...

And this will happen also...

The problem with getting the HH140 is that this will start............. and there are No pills for this...

I have PM30 and use a M-26 Motor Guard filter at the cutter, and a filter at the compressor. I have 60gal. compressor with a 110 pump and a 110 motor from a 30gal comp.Now this is not the 30XP but the use of air is about the same. My comp. never gets below 90psi when I use the cutter for a long...

Here are some flat balls, that I welded on my table for leveling.

Be for I welded these on the table legs I put a 3/16" pice of plate under the ball, so when I go to move the table the balls will be up.

I needed this to work on patch jobs on mower decks. 1 7/8" ball.

I have a Kubota B2630, can I use offbrand fluid or do I need to use just Kubota's brand ??

You have a great by at $180.00 for a AC/DC welder. I looked for a good two years for a clean AC/DC unit, but here in my area of Fl. they where used as a wheel chock or a Boat anchor....

If the Jeep is on a gravel road it would be in a ORV park or a trail some where, and the speed would be some where below 15mph. It is a 2000 Jeep with just over 13850 miles, when it sees a hard road it is form the campground to the trail. It went from the dealer to the cutting board in one day...

I have an area outside that I do all my cutting and stick work in.

You will like your 211, it is a very nice welder but you will find it hard to stop getting more welders. Its like Ice Cream....

Great thread and a very nice build..

I have a Hoist set up now I use it to lift my JD 170 and other small items. I have used this set up now going on 7 years now, the Elec hoist will lift 1300lbs. it is mounted on a steel tube 1'' 3/4'' x 1/8' wall x 11' span. I have 2 steel supports ""1 1/4" flat stock"" going up to the roof...