Search results

I am have what I assume is cavitation in my hydraulic system. The hydraulic oil shows many small air bubbles on the dipstick. When I start up my machine and lift the FEL it will start to raise then pause then lifts. I assume air in the cylinders going through the system. Kioti recently released...

Its the factory filament bulb. The voltmeter shows 12volt to it until i turn the light on

Dave can you elaborate on this, location of connector blocks and relay type? I have DK470SE cab and have radio problems as well. Sometimes it works, sometimes just left or rt speaker. Dome light does not work as well. I unplugged and cleaned a connector above the fuel tank but no luck.

Anyone have more info or a part #for this plug kit? I replaced a radio and had problems with the new radio, but then realized the dome light does no work either. I disconnected and cleaned a few connections between cab& fuel tank and reconnected but it did not help. One of the connections did...

Same experience on a TC29D without SS.

I had a Tc29da for 20 years and replaced it with a DK4710SE cab. The NH was a great tractor but I wanted a cab for plowing and SSQA. The DK is a little larger than I wanted, but I wanted the higher FEL lift capacity. A year and half later, I like the tractor and glad I got it. My only regret was...

Not much to add but in my past job I used to deal with the dealer in Katonah. I worked a mile away. They weren't a Kioti dealer then but were a good dealer to deal with. I also emailed (what I assume is the same western CT dealer) a few Kioti parts questions. They were answered quickly and he...

I agree with many of the opinions offered. A little over 20 years ago I wanted a tractor for my new property and house project. Growing up using 50s and 60s ford that's what I wanted. Fortunately, others convinced me to get a newer 4 wheel drive with FEL. The guy dropping of my tractor used to...

I am trying to remember how I dealt with this same situation. I think I loosened the bolt as much as I could. Then cut it flush to the bracket. Removed the bolt and bracket. Needle nose pliers visegrip to remove the remaining bolt end. The original bolt was long enough to cleanup and reuse. The...

Maybe not but on my DK, I filled the space between the double wall with a 3/4” pipe cut off. Longer bolts and shackle plate on the bottom. I have used them a fair amount, no sign of anything moving. I would typically prefer to weld hooks on but I think this is a better setup. If I saw someone...

This guy appears to use same type of heat clip gun

KIOTI CK2610 or KIOTI CK2610hst is another option. If loader work is important to Bill C., the loader lift capacity of the Branson or Kioti offer "real capability increase" over the L2501

I looked into these and was very interested in them. Kubota BX Tractor Pallet Forks - Pallet Fork Attachment for Kubota - Redline Systems I called and spoke to the owner about using them on my machine. He was very honest and said they would work but I would need to use caution since my machine...

I used Ken's bolt on hooks on my Kioti. I felt the bases that are on the hooks would provide extra support. The center of the factory Kioti bucket has angle welded on for extra support. I placed the clevis/plate mount inside the bucket. (Need longer bolts) The outside hook bolts go through a...

I recently sold my New Holland TC29da and bought a new Dk4710se cab. I have used a MF 1240 and I think it was about the same chassis size as the TC. I was looking for increased loader capacity and a backhoe. I barely have 30 hrs on it and I like it but the increassed size and weight is...

Doug, do a search on this forum or google. TC33 solenoid / relay problem. There was a post about someone having a similar issue. I am fairly certain TC25d, TC29d, TC33d are identical in regards to the fuel system.

Doug, a diesel engine ignites the air fuel mixture by compression. .. no spark plug. If you didn't run the machine out of fuel, or have a clogged fuel filter, probably a fuel delivery problem. I had a TC29da for 20 years. If you ran it low on diesel, it was obvious, it would spit sputter badly.

In late October I sold my Tc29da of 20 years and replaced with a DK4710SE cab. It was a tough decision but was tired of being cold plowing. I still have very low hours on it, but the few times I have plowed snow in a warm cab definitely outweighs the times I will miss the open tractor. The cab...

That's funny Rick, I never saw you over when I was plowing my driveway. You should have said hi or at least helped out. I get that the block heater only heats the engine oil but the heater definitely helps the tractor heat up quicker. The tractor would whine a lot less. Maybe on a larger...

My TC29 was loud when cold as well. If I used the block heater it would be a lot less noticeable. I think TC29da came with block heaters. I put mine on a remote switch, made life easier. Just remember to unplug it

The dash glow plug indicator light on my TC29D was hit or miss to work. But the glow plugs seemed to work regardless. When I slowly rotated the key I could see the battery light get slightly dimmer, I assume from the electrical draw of the glow plugs. I recently sold my NH, but it was a great...

I was nearly ready to purchase a Tym 474, but decided to get a Kioti Dk10se due to loader capacity and lack of Tym dealer near by. I think the Kioti is about +300 on loader capacity vs Tym. I also didn’t want to increase to the next chassis size. To me, that was a larger tractor than I wanted.

Kstone, good luck with the tractor! I have new Kioti coming soon, was looking at a bluetooth to 3.5 adaptor. Amazon has a lot of them. Similar to this. Some had a 90degree connector to reduce possibly breaking the unit off when plugged in. I liked this one...

Thank you AW! Nice graphic

Can someone provide me the measurement for the wheel weight hole spacing on a Kioti DK10se series rim (r4). I have New Holland weights off of a TC33D and they appear that they may work, probably 3 - 10 1/2" OC. thanks Bill