Search results

Any one know the part number for a 2510 cross shaft u joint? Moog or standard replacement?

Can’t believe I didn’t catch it saying international. I’ll see what I can find when I go look at it. Thanks

Looking at older smaller 15-20k lb track loaders for a little work on the farm. Found a Cat 933. Owner isn’t much help with info other than saying runs good, no leaks and under carriage is good. Can anyone tell me what series it might be? Hp? Pain the butt to find parts or run? Any other...

Thanks. I’ve been waiting to hear from someone who has their cutter.

Looking at an Allis HD7G. Any good sources for steering clutches?

I’ll have to see if I can find one close to inspect before I order one. Sounds like they may be worth a shot

Anyone use one of their rotary cutters? One friend told me about their 10’ mowers and the price is less than a good used Deere or Bush Hog. I was questioning their quality but another trusted friend said he had experience with their 3 point blades and they were stout. His opinion is pretty much...

I realize it has to telescope. Maybe I’m not asking the question properly. I’ll try it with the longer single pto shaft assembly and see how it does. If it vibrates or comes off and beats the heck out of me then I’ll switch it up.

I picked up a Woods C114 10’ cutter last fall. It was missing the pto shaft. Looking online it appears it had a 2 section driveline with possibly a carrier bearing in the middle with a shorter shaft attaching to the tractor. I’ve seen several setup like this. But I’ve also seen a few with just a...

It crossed my mind for the road grader job but I don’t need everyone on my butt all the time. And between a 60hr a week plant engineering job, gun shop and starting a trucking company I don’t need another job lol

Neighbors and I all have nice new houses and pay dearly in property taxes. It’s irritating

No pics. At work at the moment. I’d say 98% dirt and the gravel is small road rock. Usually the grader operaters just smooth it back onto the road and we get flats for the next month or so around here. I set my side linkage so it cuts more on the outside and then after a couple passes I wind up...

After advice on here I purchased an EA land plane to maintain my mile of gravel road. Does an amazing job. Talked to the road grader and he cut some of the ditches awhile back to help where they had filled back in. Should I blade the dirt/rock mound on to the road and smooth it out with several...

That does look like it, thanks. I think someone removed the original cylinder

Anyone know the model of the cutter I picked up today? I’m pretty sure it’s a Woods. It’s belt driven to the spindles and they say Woods 15184. Ordered new belts because they’re splitting. It’s 10’ outside to outside. Need to replace the tires if anyone has recommendations on what to get. One...

I made sure I boxed in the back to keep as much debris as possible inside the cutter. I was pretty apprehensive at first, my machine only has heat so I run without the door when it’s warm. A few buddies have em and they said they don’t have problems with stuff coming back at them as long as they...

No slip clutch. That’s one function of the motor relief valve, in case you hit something and over pressure it. Motor said case drain was optional. Skid steer doesn’t have one so if I tear a motor up I’ll add one. 23 gpm @ 3000 psi

She still needs paint so don’t judge her too harshly. Picked up a Deere 609 brush cutter. Found a chart that showed heavy duty brush cutters and searched till I found one close to home. It’s rated for 4” stuff. Did the formula and I’m thinking I bought a 10 ci motor. 5/8” hoses and and a motor...

I’m building a brush cutter for my skid steer from a 3 point Deere 609 brush cutter. Input shaft turns out to be 21 spline 1 3/8”. All the specs I can find say it’s 540 rpm. My mx6 is also 21 spline 1 3/8”. Was it common for Deere to use that size of input shaft for 540 rpm?

I saw they were in Sedalia, might have to take a trip there. I like that they can cut at or below ground level

Been looking up the Precision. Anything you don’t like about it? They say it’ll cut between a 9-12” tree. How hard is it to get a 12” in the jaws? It’s another 1k more than the Jenkins but the extended reach looks nice except they say not to use it to stack brush

I have a cl fab puller. Would like a shear for the bigger stuff I can’t pull

I’m in the market for a tree shear. Those that have them, do you rotate it much? Enough to justify having hydraulic or is manual rotating ok?

Any suggestions on a quality hitch mount spreader for grass seed, fertilizer and food plots? It’ll be used on our utvs and quads so it’d be nice to be able to turn it off from in the cab. Which I already have a switch and remote plug in for the sprayer in the utv I’ll use it most in. My new...

I agree with what was mentioned. Pin and bushing like they use on tractors, skidloaders and other equipment.

I’ve seen a few welded straight up, one from a guy at work. Always assumed that would give problems on the tilt. I like the idea of about 25 deg

The side that had the 3 point was mostly closed in. Was gonna weld some plate on the lower part and finish it off. And it’s squared off so it was gonna be easier

No I’ll have to look for them lol. Had a guy at work trying to convince me it mattered and had me second guessing myself.

Sorry just got off midnight shift. Converting a 3 point brush cutter to run on my skid steer. Trying to decide which side of the mower to mount the qa plate.

Skid steer brush cutter from a 3 point unit. I had planned on welding my qa plate on the side where the 3 point used to be and boxing in under it to keep debris away from me. I was told to weld it on the other side so it would throw the debris away from me and if I welded it where the 3 point...

Trying to pick a hydraulic motor for my skid steer brush cutter build. Trying to find one to handle my loaders gpm and psi is slim. But it seems most I see in surplus center list a case drain size. I just have standard flow with no case drain. Do you have to use the case drain? I’d like to use...

I could see where it would be with the front wheel. I’m going to remove my wheel and open up the front to expose the blades. It’s more for reclaiming some land then mowing. I’d rather sit on the tractor and drink a beer while mowing then sit in the skid steer lol.

Wasn’t planning on a hinged plate. But driveline should be the same. Looking at going with a 9-10 displacement motor. They have a char-Lynn that I’ll probably go with. Looks to be the only one with a high enough gpm, pressure and rpm rating. Also the most expensive, my luck as usual lol

Starting a new project and been researching and reading forums for tips and advice. I have a case 90xt and am supposed to pick up a Deere 609 brush cutter Monday. Planning on one of surpluscenters pto shaft hydraulic motors and cross over relief. Online it says my loader is rated at 25gpm and...

Ive got a tree puller and skid steer. It does ok till the trees start to get larger then there’s some time spent rocking back and forth breaking it loose. And the trees I need down are in clusters.

I’d like a Marshall saw but kinda pricey. Was bidding on one till it went way over what I wanted to give. The trees are a mixture of both. It was originally dozed and cleared. The trees grew like that then after mowing I’m sure there’s mature sprouts growing from the cut offs

Wondering which would best suit my needs. I’d like to rent to try but no one seems to have these attachments for rent. I’ve got probably 20 acres of over grown duck lake and even more of hunting ground I need to clear. I’ll be running on my case 90xt, with tracks on probably pushing 10k, 85hp, I...

Been looking for an older bush hog 406 today, supposedly rated for 4"

most of the heavier 6' I've been looking at have been around 5-700. 300 approx for the motor. I have enough steel laying around to build my qa plate and anything else. Hoses I make so possibly a little in fittings if I don't have what I need. I want an MTL but for the time being I don't see me...

Which brand do you have?

Been wanting a mower/brush cutter for my skid steer for a long time just don’t want to give 5k for one. Thinking I’ll convert an old 3 point 5 or 6’ cutter into one like I’ve seen on other build threads. Are any of the older cutters extremely tough or tougher than the rest? I know I won’t be...

I like my loegring ott metal tracks. Have em on my 90xt. When I’m in the timber or anywhere soft they’re a life saver. I think they tear up the ground a lot less than just my tires when in soft stuff. On gravel or hard pack I just make sure I take it easy turning. Makes it a whole different...

Walmart or auto parts stores here take it, they have to. Up to 5 gallon a day. Or buy an old army deuce and half and burn it for fuel

Do they make an adapter for your Kubota to switch to quick attach? I have one for our John Deere. I ran hoses from my rear auxiliaries so I can use the grapple from my skid steer when it’s too muddy out for the skid steer.

Awesome fab skills. Keep an eye on the 4 bolt flange bearings. We use a lot of em at work. When our operators are loading and unloading rolls if they bump into the the shafts supported by the bearings they have a tendency to crack the housings.

I priced out some ar500 plate. Wasn’t cheap at all.

What are you using for a blade?

I have a tree puller. I have a 90xt and you start getting close to 8” trees and it takes some time. We have a large duck lake that’s needing some attention and I thought the tree saw would be quicker. Do the manual sawfish style work well or would I be wishing I had bought a powered saw?

The The ones I’ve seen commercially had a push bar on top to guide the tree away

How fast can you raise your loader arms from the ground to full up? I believe the single gear pump has something to do with charge pressure to the wheel drives. Mine was slow when activating the hydraulics and drove "funny" till I replaced it.

Has anyone built a tree saw for a skid steer? My search isn't coming up with anything. What did you use for a blade? Any links to threads I couldn't find would be appreciated.

I didn’t think it was worth it just wanted some reassurance that it wasn’t magically a lot better for the equipment. I can probably go thru 10 gal a year. Which isn’t a lot. But it’s a lot of money for the premixed. Thanks

Anyone use the premix store bought ethanol free 2 stroke fuel? Debating if it’s worth the extra cost for the saws and trimmers.

Looks like I知 getting an Allis H3 track loader to play around with. Does anyone know if I can swap the bucket for a dozer blade?

I have a case 90xt I've been wanting a brush cutter for. I was originally sold on the mtl but had a farmer tell me about his Jenkins. I like the idea of the wheels and pivoting design. Any downside to this? The Jenkins is a bit more but not enough to turn me off from it. Anyone have the Jenkins?

I知 almost finished with my grapple bucket build and was looking at building a mower out of a 5 brush cutter. I壇 only be using it for mowing brush and small sapplings in our timber where it痴 easier to fit than the tractor. I have a Case 1840 without high flows. Doing the calculations it looked...

About to order a grapple bucket for my Case 1840 for moving brush and downed trees. Wanted to build one but I知 short on time and deep in projects. Was looking at the Titan 60? Looked pretty well build with 1/2 steel. Saw some bad reviews online but wasn稚 sure if that was from abuse and they...

Going to start building a grapple bucket for my Case 1840 once I get caught up on honeydo's around the house. Would 3/8" x 3" a36 be strong enough for the tines? I'll probably gusset them at the ends. Kinda worried about weight. Prefer not to have an 800lb grapple.