Search results

I was able to get my rake on mine, but it was TIGHT.... They definitely do not swing near as wide as my 40HP tractor does. Not sure there is anything you can do about it unless someone else has come up with a way for the arms to extend wider.

Good to know, but that still is 1.5 hrs away. I just found out about 4 weeks ago The Tractor Shop in South Webster, Ohio just became a Kioti dealer, so that is only 20 min away.

Thank you.

The new one should have the water sensor on it as well. I have never see one made for the CK without it. I would double check that you got the correct replacement filter.

It appears my local dealer has went out of business and the other dealers are over an hour away and I would like to be able to source the fuel filter for my CK4010 from somewhere else if possible. Preferably a Wix or similar. Has anyone had any luck with crossing this to a more readily available...

I have a MC600 rear discharge deck with only about 70 hours use on it. Like brand new. 2,950.

Sounds good. I’m not in a hurry and I would spend more than 15 minutes probably hooking the trailer up, setting the ramps up, and taking them down to get it loaded, then strapped in, and then doing that again in reverse when I got on site. That’s the main reason I wanted to just drive it there...

I just purchased a new 4500z and I have about 114 acres 2 miles from my home. Has anyone trekked their Ventrac that far to mow, or do you just load it up on a trailer for anything over a couple hundred yards? My Kioti CK4010 I just drive there and back when I need to do work, but I am not sure...

6” But after finally getting time to actually take a closer look at the rim, I believe the lugs came loose and caused the blowout rather than a tire failure. It appears that the holes in 2 or 3 on the rim were worn out a little oversize.

Here is the info off the tongue..... am I reading this right that I can put a 12 or 13” tire of a 13” rim??

Ok.... Well I have a 2005 Triton trailer, aluminum frame with the marine grade plywood decking. I think it is a UT128, or similar.... but the issue is I was going on a trip that would be about 700 miles round trip, and would be hauling back about 700#'s of equipment. So before going I checked...

Has anyone had to replace one of these? If so, did you go factory or use one of the universal polyurethane ones like from Energy Suspension Parts? Here’s a pic of mine. I’ve halfway tried to pull it back over the joint but was afraid of tearing it.

Well I guess hind sights always 20/20, right? Just looked at another building - 24x30 - I had built back in 2002 and I never removed the sod on it either. If fact I don’t remember the concrete guy removing the sod from it before pouring. If he didn’t, it’s been 16 years and, knock on wood...

Some pics with the metal all finished up.

So... putting up a 24x32 pole barn and it ended up being on more of a slope than anticipated. I’m curious as to what sort of economical recommendations there would be to prep this for a concrete slab. My plans were initially to only pour a 4-5” pad using fiber infused concrete. I’m just not sure...

Hello... Have someone wanting to sell me what I think is a Case 310G, but the serial number they sent me doesn't seem to match with any years that the 310 was made, for any model. Anyone know by looking the year/model of this?

Cool... Well I do know I have pushed mine to its limits as well... using the grapple and either a box blade or bush hog on the back... lots of spinning... however, I put the backhoe of it a few days ago and was picking up probably 1,000 pound rocks in soft dirt and no problem!

Just tried another Donaldson site and same results..... seems strange if Donaldson is making these filters they don't list them.... plus when I tried by manufacturer it didn't even have Kioti on their site... they did have Daedong, but the only tractors listed were DK series, and when I selected...

Anyone have the Wix cross reference numbers for the following: They are having their seasonal sale thru the 24th so you can really save.... Hyd Filter - T2185-38031 Fuel Filter - F6800-16411 I believe I have the correct ones for the following: Air Filter - E7230-11081 Wix - 46489 -Outer 46490...

Just heard from the local SWCD folks... just as an update: I again talked with our engineer, and I also figured the acres of watershed for your pond. So with not being at your pond site before, the numbers are rough estimates. I came up with 32 acres of watershed for the pond. From that ran...

Phil, I wish... but I do not see anyway since it is all higher elevation... see attached below:

I am attaching a few pics to show the conundrum I'm in right now.... it is a new pond, just built it last summer and I obviously miscalculated the amount of water coming into it as it filled the 18 overflow pipe I have and then ran over the dam.... prior to that it had already ate the overflow...

Ok, I know this is a stupid question(s), but I am just not sure the manual is correct on this. It shows that the drain plug for the hydraulics is the one labeled with a number 1 in the pic below, but it looks to me like that is one of the bolts holding the rear end casing on, and not like a...

Well, I went to the dealer and had them look it up and they couldn't find just the c hook and clevis pin, but they did find it without the whole stabilizer arm and just the "link section" with the part I needed included for 20 bucks. Here is the part number.

Bush hogging the other day and I snapped one of the clevis pins like in the image below on one of the stabilizer bars and I need to get one, or two, and I'm at work and would like to order them from TSC and pick them up on my way home.... Before you ask... I called the dealer, didn't have a clue...

I have a 2016 Kioti CK4010 and the dealer sold me the filters and fluids for the first 50 hr change at cost.... but, the hydraulic fluid above is evidently what they use in their tractors and I am not sure it is all that good, or right for my tractor. From TechSelect's website it says it is...

Just purchased a new CK4010 and I now have 10 hrs on it and both the transmission and front axle dipsticks are showing no oil on them or just barely on the bottom..... Background.... I'm pretty **** about fluids and fluid levels, so after it was delivered I checked trans, front axle and oil...

Hello, first post but been gleaning the site for a couple of months. I just purchased a CK 4010 with FEL and BH and then had the dealer add the 3rd function and a grapple bucket. The issue is they delivered the tractor today and unfortunately the grapple wouldn't work. To make a very long story...