Search results

Your most welcome, hopefully it helps!

Huh, I couldn’t remember for sure if it did or not! [emoji57] guess old age is creeping in.

Sorry was on app for phone! Can you see them now?

I removed the whole gear box from the deck and took it apart to check and clean it. I don’t believe you would have to completely disassemble to change the seal. Let me look and see if I can find my pictures I took tomorrow. Also I believe I have the part number for the seal I used that I can get...

Sliderbuck, yes it does have a seal on the input shaft! I had to replace the seal a couple years ago on mine. Do to tall grass getting wrapped around the shaft and making its way into the seal causing it to leak!

I bet your getting a cast iron frying pan for Christmas now! [emoji51]

I am 46 Two One at 74 One at 30

It is true Coobie.

Nice buck, but to bad it’s from a deer farm. I drive by it twice a day.

Take it somewhere else please!!!!!

This is the letter I received!

This is his setup!

My brother is in his first year of collecting maple sap and making syrup!!! I am contributing by dropping sap off to him from my trees. My question is today he pulled out 3 jars from his first 3 batches and I couldn’t believe the difference in the color. What causes that??? He said he finished...

I was able to finally move a little snow!

Hey Mow, A few weeks ago I went out to pick up leaves and noticed rear tires looked low. They are loaded with rim guard. I get the valve stem to 12 o clock position. Go to grab the cap to remove ever so lightly and next thing I know I am being sprayed head to toe by rim guard. So I plug the the...

Is this what you need?

Disregard

Ok I installed my mower deck on my Emax 25 today. Put the height adjustment knob to install. Lower your three point hitch all the way down and shut tractor off. I had to use a pry bar for a little leverage to move this bracket down to install the pin. Then put the pin in the front of the black...

Barry, I purchased a emax 25 December 2015 and mine came this way.

That's easy Eddie, just fork over the cash. ;) I just went for my first time with my parents. We left August 28th and got home September 11th. If I didn't have the wife and daughter at home I would have stayed. My dad got his Cape Buffalo! And I got the Warthog.

Need to paint the Deere 317 engine, it has already been primed. Any thoughts or opinions on the best brand of spray paint to use? Mike

Does anyone know where you can purchase lift cylinders for a front end loader on a L48? My uncle bent one of his beyond repair. They want $800.00 for one from the Kubota dealer. “D” ROD DIAMETER 1.375 “S” PIN HOLE ON THE ENDS 1.2 “E” WIDTH 2.450 “G” 2.9 BORE 2.25 FULLY RETRACTED 32 ¾ FULLY...

Could anyone tell me what Model tractor this fits on! Thank's for your help. Mike

I purchased a Ieski TU 180F a year ago along with the tiller and have found a little information on them. So I am going to post pics of my tractor and general information that I learn or find along the way. I am hoping this will help someone else in the future. It take 5qts of oil when you do a...

I am curious what the box that is connected to the back side of the clutch is for? Is it a wet clutch system? It has a plug on top to add fluid, and bolt on the bottom to drain and a bolt on the side, that I am guessing is to check the level of fluid! Also what type of fluid do you add to it? Mike

I need to change the tranny/rear end fluid in my TU 180F Landhope. I have tried to find a solid answer but have not been able to. Do I use hydraulic oil or gear oil?

1.Ok you have the key to start. 2.The red button you push to warm glow plugs. 3.Lever is for throttle. 4.Dummy light below battery light is to tell you glow plugs are warm enough. What is the battery light for, and what is the other place on the dash that looks like it is missing a knob for?

My Father just purchased a TU 180F! I noticed on the right side of the steering wheel on the gauge panel, their looks to be a opening where a pull switch is supposed to be but the knob is missing. Anyone know what this knob is used for? Mike