Search results

my cuz has a 3610 that you have to spin the starter a long time when it's cold. It is like it has lost it's prime in the pump. He has to give it a little shot of start fluid in the morning to get it going. It will start the rest of the day after it gets going in the morning. Is there a check...

I got a buddy with a 3940 about 10 or 12 years old and it started with the lift not going down without weight on it. with a disc on it ,it will go down to the ground but with nothing on it won't go down. He has move the response slow and fast lever back and forth without change. Has anybody had...

I got a 1987 Ford 3610 that has to crank a long time when it's cold but cranks right up the rest of the day after that. I just had the injectors rebuilt. It runs like a champ after starting . It's got clean exhaust no blue smoke. I can give it a little shot of starting fluid and it cranks right...

My cuz ask me to post this. He's got a 1964 ford 4000 diesel 4 cyl. that revs up and runs away when it's cold but quits when it warms up. the throttle lever loses any drag on it as it revs up. It has a rossa master pump on it that was rebuilt about a year ago and has been working fine. the...

I replaced my key switch with a ford switch. it's different so I plugged the wires into the same numbers and it don't want to crank without grinding on it for 10-12 seconds. At first I had the starter plugged in to second position of switch (two click on switch) and it crank good and moved key...

For about a year the rpm's come up slow, it don't respond to throttle right away and it has bad knock on the upperside around #3. I use it to roll hay so I throttle up and leave it alone and it had power. Last year about every 45 minutes it would run hot and we stop and added water and went on...

I ordered (2) slave cylinder kits for my case-ih 1494 brakes. They sent me the wrong parts that was shipped directly from Rock Valley,Ia. I called the folks at Case-IH and they were nice about it and said it was their fault and would send me the correct parts. They ask for a picture of the...

I have a Farmtrac 555 that is leaking oil around the steering post under the steering wheel. I have looked at the parts diagram and it shows only a dust seal under the steering wheel in the steering post. It doesn't show a seal or o-ring where the post goes in the steering motor.Must be one...

I have a ford 4610 without factory hyds. I added a adapter block and the wrong spool valve to start off with.I bought a new spool valve and put it on. a prince 20 gpm RD-2555-T4 ESA1 DA OC valve. After I put it on it squeals when operating the valve. Both hoses jump with pressure when the...

I have a claas round baler. My question is where do I find aftermarket metric chain.I haven't seen any in catalogs.How is it sized as compared to 40-60 roller chain on U.S. stuff. I'm looking for a cheaper alternative than buying chain from the dealer.

I got a farmtrac 555 with about 90 hours on it. The lift would not lift for several minutes. I changed the oil using universal oil and changed the filter. It is still the same. It works fine after the pump primes. Anybody got any ideas?

I can't find a web site with Illustrations and parts numbers. I need a fan blade and some sites show blades with numbers only and the ones that give model numbers don't have m-4050. I did not get anywhere on Kubota site.HELP

I am adding aux. hyds to a 1984 4610. I put on an adapter plate and ran hoses to a single spool valve.The plate is stamped with a"P" for pressure side.I hooked it to "in"port on spool valve.I hooked it up to a batwing rake.I had to kill the tractor because I had fluid pressure on one hose,but...

I recently bought a farmtrac555 2-wd 2007 model.It was parked up for a while before.It has started leaking hyd.oil very bad at the rubber boots on both sides of the back end where the brake pedal shaft goes in the back hub.I assume the rubber boots are just dust and dirt protection ,they both...

I bought a 1984 ford 4610 2 wheel drive at auction.It doesn't turn sharp at all like normal tractor .If I screw out the steering arm it's just gonna turn sharper one way and less the other (I think).The other #'s by the serial # is 4H275 and DA314C which I guess one is the model#.I think it must...

I bought a ford 4610 at auction that came from a county road dept. I've found out there is 3 models of this tractor.One model is "highway". I think this might be mine as it does not turn sharp at all. Is there a way to fix this or modify it to turn like a regular tractor.any help thanks.