Search results

was using the back blade to clear some snow this am and i noticed that every once in a while i would raise the back blade and i would come up to full height then drop a small a mount suddenly and catch again. Fluid levels seems fine and fluid is clear. All other operations seem normal. This just...

Need to get a new set for the front of my JD 3720 (size is 27-8.5-15) been trying to find something similar to the ofa easy on 5 chains i have in the rear- euro style low profile hard wearing For some reason better quality chains seem to be in short supply in this size- anyone got good sources...

Well the current cold snap seems to have shown a weakness in the battery of my 3720. At -30 and only and hour and a half of being plugged in the tractor would barely turn over once - did get it to start with a charger/125amp booster but i figure its an indication the end is near. I did a search...

Yooperdave's thread reminded me of the challenges of finding front chains for my 3720. One of the things that might make it easier is knowledge of alternate sizing that is the same, pretty darn close, workable, or can be trimmed to a great fit. First there is the issue of the various numbering...

I have had poor results with conventional ladder style chains in the past as far as grip and chain lifespan. Following the advice is some of the chain threads i looked for euro style chains for my JD3720. Having found some availability issues and pricing circa 1k$ i contacted windy ridge...

I need to replace my cutting edge on a pronovost rear pull somewhere i read someone that posted they welded on a narrow strip on the base of their cutting edge which gave them a much better scrape as replacement edges in hardox are quite pricey i wondered if it would be possible to weld a...

Have already worn out the tire chains.com front chains on my 27x8.5-15 r-4's When they arrived it was obvious that they were not in any way beefy enough (I think that they were intended for a lawn tractor) but I used them anyway. So now I need a new set, usage is on pavement so ride quality...

i have a jd 3720 and a pronovost pull snow blower, at operating speeds the chute rotation is way way too fast and the diverter action is also too quick. I have been thinking of restricting the flow but wondering about the best way to accomplish it. I see that there are fixed orifices and...

Howdy, hoping someone can point me toward the color and location of the leads for the work lights on a ROPS 3720. I thought i had read some where that they are just sitting somewhere in the rear of the tractor waiting to be tapped into. Thanks

cross post from customization: Tried searching and did not find anything recent, at the rate LED technology is changing i thought i would ask anew. Been looking at something like : Amazon.com: OPT7 LED Headlight Bulbs w/ Clear Arc-Beam Kit - H4 (9003) - 80w 7,000Lm 6K Cool White CREE - 2 Yr...

Tried searching and did not find anything recent, at the rate LED technology is changing i thought i would ask anew. Been looking at something like : Amazon.com: OPT7 LED Headlight Bulbs w/ Clear Arc-Beam Kit - H4 (9003) - 80w 7,000Lm 6K Cool White CREE - 2 Yr Warranty: Automotive for more...

so i went to test the relief pressure on the cushion valve on my chute rotator and could not get any change either with screw all the way in or out. And a fitting that had previously not been leaking was now leaking like a sieve. So i pull the connections and inside it appears that some portion...

My new pronovost blower has cushion valves on the rotator and i need to set them. Have been thinking about getting a 5000 psi valve and teeing it in between a male and female QD fitting , seems like this would indicate the pressure in the lines to the rotator as it relieves. Wouldn't this set up...

i have couple of questions for setting up a new rear blower how to best size the pto shaft and cut it recommendations on size of hydraulic line for rotation and chute deflection how to best determine the length for the hoses Many thanks Bill

Anyone else have issues with start-up smoke in their garage or small building stored tractor? I've been thinking along the lines of trying a short piece of heat resistant flexible tubing or hose to route the exhaust out the open garage door. Slip it over ,start and warm up indoors, remove and...

asked local dealer for 3901 equipped as follows: l3901 La 525 loader w qa bucket Pallet forks 4wd Loaded tires 2 link chains, square lug type Top and tilt- I guess it needs to be after market Quick hitch- land pride? 3 rear remotes Telescopic stabilzers Cruise asked them to separately price...

debating upsizing to a bigger orange (dealer nearby and well regarded) tractor from b3030. Thinking of just going to to smaller l to retain access to some areas i ve that are congested I have read on some threads that hydraulic options on the basic tractors aren't as well done - i.e. location...

Have had a B3030 for about 9 years, been a great tractor but always seemed a bit too light/small. Originally got that model due to hp at PTO with small, maneuverable size. Current main/ most important use is clearing my 1/2 mile drive and my neighbors offshoots. For this its been ok but we...

Howdy, hoping someone knows the diameter and thread pitch of the bolts that secure the folding rops in the up or down position I am thinking of using the empty nut to mount a rear facing led worklight. Many Thanks

I can't seem to keep the edging material (I think it may be called trim-lok) in place around the edge of my seat. Once enough of it comes off it becomes a bear to get back on over the seat covering around the corners. I am thinking of contact cementing the actual seat material to the metal seat...

How steep a grade should I be able to pull with a 3030,tires loaded with rim guard and loader(empty) ,in high range? Could not pull a hill of about 20%(NOT DEGREES) the other day,even with the engine at PTO speed. I will try to measure the slope when I get home-but it seems like it shoud pull it...

Ok need some advice here's my situation Have a B3030 with front blower and landpride 1572 backblade for dealing with snow (about 125" on 1/2 mile gravel drive) The other main usage for these implements would be maintaining road and drive. The blower works great but I find that carrying the...

still waiting for the subframe for my front blower but took delivery on B3030, 72in landpride backblade and 403 loader today. cleared the drive and did a little grading- seems luxurious after my ford 1710- very good on fuel too. Thanks to everyone for their help here.

Now it's my turn to ask the old-what should I get question. here is my situation. Have 2 properties: 1-6 acres mostly forest and scree some mowing (mix of brush hogging and small lawn),hilly with 1/2 mile gravel drive in northwest Montana. we get a little over 100 inches annually but usually...