I recently purchased this tractor and I'm looking for a soft cab for it. I just need the cab to keep the snow off of me. Hard cab is available for +/-7000 bucks and it includes AC, heater, etc. Don't need that.
Anyone have info on a soft cab for this tractor?
I'm attempting to install a rear wiper kit on this tractor. The instructions say to run a connector and the washer hose through a hole in the ceiling from under the roof area. I found the connector and hose but there is no hole in the ceiling for this to happen. Any advice would be greatly...
My DK4210 Kioti tractor did not come with a "fast dump" FEL function because it has a glass cab. The same model tractor without a cab has this function as standard equipment. Difficult to understand the reasoning behind this. Has anyone experienced retrofitting a tractor with "fast dump"...
Purchased a kit and it is very hard to read the instructions and the pictures are so dim they are almost worthless. Wondering if anyone has experience installing this kit? Does the roof lift up like its on hinges to get at the wiring? Any other tips? This wiper should be standard equipment in my...
My PTO snow blower apparently rides up on the snow even though it weighs 650 lbs. This happens if I try to go a little faster. I have the skids adjusted at minimum height. Is it wise to angle the blower such that it would get a better bite? I think just a few degrees would be all that's needed...
Hello
The loader comes with a bucket level indicator which only works when the bucket is on the ground. Is there an indicator that will tell me if my bucket is level when raised above ground level? I have pallet forks that attach to the bucket and this is would be very desirable when unloading a...
I'm considering ballast for my tractor tires. Beet juice seems to be recommended most frequently. The literature states freezing point at -35 degrees F. for RIM Guard which appears to be the only juice source available for this application. Other literature about beet juice, not RIM guard, state...
There are two female hydraulic quick disconnect(QD) outlets on the rear of this tractor. The operators manual doesn't say what model they are.
There are a few versions of these QDs and some are not compatible with each other. There are quite a few posts concerning using these outlets so can...
A question on loader removal. There are several notches on the loader "kick stand". My manual doesn't say which of the notches to use for this loader. The question is which notch shall I use? I assume the multiple notches are there to accommodate other attachments?
Thanks
Hello
Two questions about this tractor.
It has a hydraulic rear auxiliary output but no front auxiliary. Is it feasible to run hoses from the rear to the front? Lot less cost than a 400 dollar third function kit and no hassle to mount the control.
I've noticed that when in 2nd or 3rd speed on...
I have front mount mid PTO snow blower on my HST JDeere small tractor. I'm going to upgrade to a higher HP tractor, not JDeere. I'm considering a rear mount 3 point snow blower because of the cost difference and the hassle of connecting the drive shaft to the mid PTO, etc. Trying to decide...
I have a Deere 2320 tractor. I'm wondering why the U joints are all non sealed unit's? When was the last time we had to grease the U joints on an automobile? This tractor also has a U joint that is almost impossible to get at. In fact it is so well hidden Deere forgot to mention it in their...
Hello
I'm sure this has been discussed numerous times on this forum but I can't find it. I want to install a power beyond for my tractor. Deere wants over 500 dollars for a kit. Just the kit, install is more. Just a simple hydraulic outlet and return for a small back hoe. Any ideas for a less...
Hello
I have a JD2320 tractor and would like to add wheel spacers to make it a bit less tippy. These tires and rims have got weigh at least 200 pounds. I'm wondering first of all, are wheel spacers a good idea? And second I'm wondering how hard is it going to be getting the wheels back on? I...
I would like to attach a buckthorn puller to this tractor. The puller has a cylinder which squeezes the plant. I've had quotes from 600 to 800 dollars for the install of needed equipment. There must be a less expensive way to do this. Would it be possible to use the 3 point hydraulic system? Any...
Hello
Dealer is selling this combo for $16000 which includes 7% sales tax. I drove it around the lot and every thing seems to be working. Is this a good(reasonable) price?
Thanks