Search results

I have a Honda 5hp motor from a dead pressure washer. I want to put a transfer pump on it.It has a 7/8" horizontal shaft. All the trash and transfer pumps I've seen have a 3/4" shaft. ????? Are there no pumps for 7/8 shaft????

I need to store my hay in a loft above my horses. I realize that's not ideal, but because that's the reality of the deal, I want to see if I can do some things to make it safer. As I only bale my own hay, I have some flexibility. I only bale in perfect conditions. Putting up hay that's even...

I have an old 350 sickle I am trying to get running on a Kubota 4050. The lift mechanism clevis pin is to big for the hole in the drawbar, as well as being too far away for a proper hookup. Is there any reason why I couldn't simply put a big chain clevis on the drawbar, run the chain from the...

I've inherited the worlds oldest, worst maintained tractor in the history of inlaws. I've gotten all the fluids and filters done- the trans filter had a piece of a coke can in it... And I've found all zerks except clutch bearing and steering. Yes, I have the reprint manual I found but it does...

There are two wires with female connectors hanging out on each side of the top front of my 8560 cab, inside of the OEM lights. Anybody seen these or know what they are?

a little help please... Case 685 running fine at noon, run kinda hard, shut it down without idling it, 30 minutes later wouldnt start. 60 degrees outside. No smoke while turning it over, so no fuel right? Ethered it but it died as soon as out of ether. Could fuel filter have clogged that fast...

Im 99% sure I know the answer to this, But might as well ask... 2255 fel wont fit on a jx95 will it???

Ive just purchased an IH 5100 "soybean special" box drill. Not knowing what a SS is, I researched others for sale and the SS is cheaper than a reg 5100. Why is that? What did I give up, and will this hinder its use planting sunflowers??? Thanks In Advance

Sorry if this has been asked 1000 times but will moving from turf to R4s on a l2850 require new wheels?

My new tn75d-well, new to me with 600 hours has a light on that looks like this...(O)... except with an exclamation point in the middleof the circle . They "forgot" my manual. They say it's no big deal, but the power shuttle keeps poppin into neutral. Im about to send it back... any ideas before...

The dealer I bought my tn75 from has a 2wd tn75 on the lot with a cab. Are these things interchangeable? ie, could the dealer take the ROPS off my machine and put a cab on it off another tn75? Am I reaching here?

It took 2 months but I found a fwd TN75 with a Power Shuttle Trans and a good loader. No Cab, but I can always trade up later. She's a 2002 75da with 680 hrs QA bushog loader and 3 remotes, loaded R-1s, and even has a radio. woohoo!

Well I love my little tc40d, but after 3 months I have accepted that it's just not enough machine. I need a full size frame, more weight and more power. It will handle a roll bale up front, but want to tip over if you want to move it. It's got alot of weight and traction, but not enough to pull...

Well the Midwest cutter I bought out of ignorance is still in the shop-10 days now. They cant get parts, yada yada yada. The slip clutch never slipped, killing the tractor 3 different times. The tailwheel seized up on its spindle-apparently a common problem with these cutters, spun the bolt and...

Well, Ive put 50 hours on my TC40d in the last 30 days and have learned a lot. 1-Most importantly that a stump will completely stop my tractor and whatever a slipclutch in my cutter is, it doesnt work. Ditto for old crossties. 2-Some roll bales are heavier than others-which I found out after...

Important hydro accessory

Post deleted by oldforestor

Had my new/used 2001 tc 40 hydro show up today. I cant get it into 2wd from 4wd. lever seems stuck? Since there is no clutch, Im suspecting that little rod end under my left heel might be a clutch for pto engagement? Dealer gave me a gear tractor manual so Im kinda in the dark. help finding a...

Well you all wont have to answer stupid buying questions from me anymore-well the operating forum still has me I guess. Signed for a TC40DA hydro with fel and 5 ft bushog today, with 350 hrs, for $17500. figured with the hydro i better stick to 5 instead of 6ft on the mower. Look out, dumb...

Is the width of the rear axle adjustable on the L2900? i.e. can I widen it to handle a roll bale better? Thanks

Went to the Massey dealer today to compare these two as the pricing reports on here made the 1400 series look like a better buy. "...hadnt had one in a coon's age" he said. Apparently theyre quite popular here in KY and sell out fast. Are they less expensive for a like machine? Should I wait for...

tc35 with nh loader @ $19,331? thanks!

Dealer quote 2004 TC35 w/NHloader $19,331 fluid filled ind tires Thanks! <loader is 16LA trans is shuttle no supersteer thanks >