Search results

Dash display got flooded and not working. Anything to check first before replacing at cost of $1200? Checked fuses and seem good Any way to check that power is getting to the unit?

Dash display got flooded and not working. Anything to check first before replacing at cost of $1200? Checked fuses and seem good Any way to check that power is getting to the unit?

Opinions on installation requirements and problems

Can someone tell me where to locate the temp sensor on a Kubota m5040? Temp gauge does not work and I have a replacement but cannot find the location of old one

Temp gauge on Kubota m5040 quit working Bought replacement temp sensor but can’t find old one on engine Where located?

Any suggestions for a tractor canopy Have Kubota m5040

Slow leak from my rear function for my hydraulic upper link Coming from around where the house connector plunge into the rear remote Cleaned the connections O-ring or seal of some sort?

Temp gauge on m5040 quit working Other gauges working Where is probe or temp pickup on engine?

What you guys find to be the better way of fuel transfer to get away from lifting 5 gal jugs to fill tractor Don’t use enough for 50 gal drum with pump

Box blade on Kubota m5040 very hard to adjust tilt side to side Can turn lower link small amount Any trick to this?

hard to start first time each day. if I pump the plunger on top of fuel filter it will start easily and then no problem starting rest of day. I replaced the in-line valve near fuel pump but cannot find another. ??????? evidently loosing prime overnight.

Have Kubota m5040 and will need to mow approx. 24 acres. Opinions on size mower, single or batwing type for this size tractor

M5040 used for 6 hours then engine started bogging down a would only run at an idle. Then would not start and run at all. When checking everything I noticed the fuel cap was missing. I either left it off completely when filling earlier or did not tighten. Have 1/4 tank of diesel. If something...

I have a Kubota M5040 4wd with FEL. Need to replace old 5 ft cutter with a 6 foot. Looked at Rhino and Bush Hog. Want something as heavy duty as the tractor will handle. Very rough cutting needs. Anyone matched up cutter with M5040?

Hit stump with cutter today and smoked the slip clutch and the blades would not turn. Can i tighten the bolts on the slip clutch assembly and correct the problem? Appears to have about one quarter inch of material left.

I have an M5040 with FEL. When using a boxblade and pushing trash in reverse the lift arms will move up when pressure is applied leaving pieces behind. Is this a draft setting problem or what? I have tried the draft control lever up and down with no changes. It also seems to be more sensitive...

After working in some thick brush the FEL will not raise or lower when the 3p hitch is fully raised. If I push the lift lever down about 1/2 way the FEL with work properly. If the 3p hitch is raised fully the FEL will only lower by pushing the FEL lever all the way forward to the float position...

I was looking at the M5040 models and the M5640 was suggested to save $. Not as many bells and whistles supposedly. Any advice on the difference for the $ saved?

Problem with keeping implement in position. Set bush hog at correct position and it drops down completely. I must hold the lift control lever to keep at correct height. Let go of the lever and the implement slams to ground. 70's model ford 3600.

Problem with keeping implement in position. Set bush hog at correct position and it drops down completely. I must hold the lift control lever to keep at correct height. Let go of the lever and the implement slams to ground. 70's model ford 3600.

Problem with keeping implement in position. Set bush hog at correct position and it drops down completely. I must hold the lift control lever to keep at correct height. Let go of the lever and the implement slams to ground. 70's model ford 3600.

Ford 3600 PTO jumps out of gear when bushhogging. When bushhogging pto shift lever moves forward and pto stops turning. What to do?????

I have a 1974 ? Ford 3600 that my father used on his 80 acre farm. Bushhogging has been the greatest work performed with some disking and planting. Dad died 3 years ago and I want to keep the place in decent condition but I spend most of my available time working on tractor. I have replaced and...