Search results

Does anyone know about Farm Tractor Supply ???

Bought clutch plate and thrush bearing from Messicks 197.00 for clutch and 51.00 for the bearing. Could have gotten clutch for 74.00 or clutch, pressure plate, thrush bearing and bearing for 144.00 From FARM LAND TRACTOR SUPLY. Below. 37300-14500-KIT- Kubota CLUTCH KIT (0) Reviews: Write first...

Getting parts for 2000, L2500 Kubota with FEL, throw out bearing and clutch replacement. Dealer wanted 2,500 to 3,000. My first time. Will look at some youtube. Any advise on this procedure.

I had VPN on. Turned off and no problem. Anyone know why Tractor Forum is down? Says page is not working.

Today, my 2000 Kubota L2500, when pressing the clutch, it makes a squealing sound. It has never done that before today. Any ideas?

3 point lift arms were not going all the way up, PO had the stop a little before highest point. I readjusted the stop so it would lift all the way up. Several days later I was doing some dirt hauling with the bucket and noticed the boom was very slow going up and down, had to put it in float for...

I have to put new seal kits in my boom hydraulic cylinders and the New Holland dealer wants 250.00 each kit. Is there somewhere that is cheaper??

Is there a PCV on a 2004 New Holland TC30 Tractor??? Thank you

2004 New Holland, Hist TC30. Bucket on ground wont curl and lift wheels offf the ground. Any ideas, why not??

Anyone have manuals for 2007 TC30 that they could post a pdf??

This is what I get and I have posted other pics same as these. Couldn't find that... The uploaded file is too large.

This is what I get every time I try to post a pic, (((Couldn't find that... The uploaded file is too large))). I have posted other pics, what is the problem?????

Been raining off and on past several days. Finished wet sandblasting this morning and then primer coat put on. After sandblasting I used my leaf blower to dry and no rust. To keep my sand dry I drilled a 7/16 hole in the 5-gallon lid and ran the sand feed tube thru it. I used a total of 12...

Wet sandblasting my brush hog with a 28.00 Amazon wet sandblaster. Wet sandblaster well worth the money. Will paint Kubota orange. Next project is to wet sandblast the smoker firebox surface rust on 3/8 " thick sheet iron and paint. set sand in a bucket in back of truck, if sand gets wet it...

2007 New Holland TC30 when I push the brake pedal it makes a rough noise for about 1 second and goes away. How do you know when the brakes need changing, where are they and how hard is it to change. Thank you.

Anyone have an owner's manual or know where to download a free pdf for a 2007 New Holland TC30 with a 7308 FEL???

I also have this posted on TF. Lost 2 pins to my ROPs, they are also same pins that are on the loader. I have searched to no avail, also searched by picture, nothing.

If your FEL is slow, take the boot off the joystick and check that all allen bolts at the base of joystick are tight. My bucket down tilt got from slow to not working, I finally took the boot off and one allen bolt had backed off 1\2 inch, it was not letting the joystick engage the tilt down...

I want to replace the valve on Mitsubishi 28HP with front end loader, with a valve that has float. I can't find any info on pump that tells GPM. anyone have an idea of GPM. Thank you.

If I remove the drawbar and replace with chain will my 3 point landscape rake float ? My property is very rough, no way can I lift and lower constantly trying to use the rake.

Mitsubishi MT2801FD. Put the front axle gear case and king pin case on the tractor and did the smoke test. Drove around in 4 wheel drive for awhile, till started raining. Put it back in the shop and will check for leaks on the floor. So far so good. A big thank you to all the members that...

Got it all back together, now have to get help to pick it up and put in back of pickup and unload at my shop. Don't know what it weighs but can't lift it off the bar. Brought it in, in pieces. Will trim off gasket material after I torque the bolts, has to set up before tightening the bolts.

For Mitsubishi 2801FD front axle gear case, oil seals and O rings. About a week before delivery. Will post when fixed.

All I need is oil seals but you never know, so I sent these part numbers and waiting forconformation.For MT2801D I have read the procedure many, many times, almost memorized, hopefully will go smooth. A lot of thanks to bmaverick 1-Bushing-05605-06040 1-Oil seal-0840 1060 759 1- O ring-1980 3174...

I got the Parts manual, Repair manual, and owners manual, earlier this morning, have been doing a lot of reading last several hours, so now I can do all repairs and answer all my questions and can get all needed parts. I can't even begin to count the hours I have been on internet and phone...

Mitsubishi MT2801fd 4x4 with loader Fluid running down on inside front left wheel. Need help on replacing oil seal, maybe bearings, I can see on inside rim where about 5 inches is being rubbed by something. Can't see that it is rubbing anything, maybe a rock or stick got behind the rim. If...

For the past 10 years or so I started using my cc for everything I would normally write checks for, utilities, insurance, food, gas,property tax, etc. Each month I pay the balance the statement shows. Therefore I do not pay interest on the card, secondly, I get points worth cash, every 4 months...

Spilled a gallon of diesel, it went under the tractor on the floor in my shop. How is best way to clean up, or how long would it take to dry.

No thermostat in my Mitsubishi MT2801 4x4 diesel. Anyone have a part number, also what kind of coolant do I need.

Been trying to figure out a way to see what angle the bucket is when down low on the ground, can't see the sides or the front of the bucket. Thought of a mirror but no where to put it so it does not get knocked off. Got to be a better way than getting off the tractor and looking every time. Any...

Mitsubishi MT2801fd 4x4 Under the seat is a dipstick that says OIL, what kind of oil does it require, motor oil or hydraulic oil and what weight. Where do I check and put hydraulic fluid. Thank you

New to the forum, I have a Blue Mitsubishi MT 2801fd with loader. From Oklahoma city.

Blue Mitsubishi 4x4 Mt 2801fd with loader, 34 HP. Very nice tractor, no dents in it, paint is original and in very good shape, no fading, was garage kept. I had been looking at tractors on CL for a couple years, so seeing what they sell for and they sell quick, this seemed like a pretty good...