Search results

My tractor is 2 years old and mostly kept inside. It is open face unit so the weather is a factor on the seat when outside. As the seats get dry in the sun and elements then cracks will start at the bending points when sitting on it. It has not happened yet that is why I am posting this. As you...

I picked up some 2 cycle oil yesterday. The dealer said this Opti-2 stuff will do all 2 cycle motors no matter the mix ratio. One mix for all motors. They have been using it for a few years (not sure how many) with no issues. Any one else use it and what is your thoughts on it. Al

I have a Phantom 3 Pro, 4k camera. While I have had lots of fun with it and taken many photos that I can send by e mail. The videos are to large to send. I have edited them down to the point where they are useless to send. I have tried a google search and the sites are not very user friendly for...

First let me say like the subject line states I have no clue how to weld. I also don't know the lingo. I have tried in the past (only when needed ,bad idea) and it either looked blobs of crap or it didn't stick, sometimes both. I do have a welder and gas. The welder is a Lincoln Mig Pak 15. It...

I was only on this forum (my first) a short time when started to notice how many TBNs tackle tractor problems head on. Tractors are used in many different ways so each unit is not made for everyone. No one wants to just work around a problem, it has to be better. When I had my other tractor...

I am looking for the Rustoleum lobster red spray paint. It is the color match for the new Kubota from what I have read on TBN. The issue I am having is that I am in Canada and couple of the local supply stores that have Rustoleum products can only carry the industrial line. Lobster red is a box...

I am thinking about getting a trailer. It will be a 16 to 18 feet car or deck unit. Something for the older car, tractor, and just hauling anything. I know if I have one family and close friends will want to use it from time to time. I have no issue with that but if the unit has electric breaks...

Well I guess the title says it all. I thought all 3 point pto driven implements were 540 RPM. On what implements would the 960 RPM be used. My first guess would be a implement under little load so the engine could run at a lower RPM like a generator or a water pump. I am sure that it is on the...

It happens every year. When blowing snow yesterday I found the sales flyers. They are rolled up and put into a tube type plastic bag and dropped at the end of the lane. With one large snap it broke the shear bolt on the blower and it seldom hurts the flyers much. Over the years I have put...

My B 2920 has a easy to read dash board in the daytime. At night the needles don't go out far enough to see them in the lighted background on the outer edge. Is this just me or is this a issue with the B series (not sure about other units) and has a fix already been put in place. Al

A couple questions about warm up time. My B2920 is in the unheated part of the garage. It has no warm up heater ( it didn't come with any) to plug it in. How long should it warm up after started when it is a few degrees below 0 (0 to -10) . Blowing snow is hard on a the unit as it is wide open...

The B2920 is getting close to the 50 hour service. I thought it would be easy as I would not be the first doing this. Well I searched the "50 hour service" and when reading through the posts it is not as cut and dried as I would have thought. So to the service manual and it only has the engine...

I have turf tires on the B2920. What is a good all around air pressure (front and rear) for cutting grass (MMM) and some FEL work with a weight box on. Do they have to be at max pressure or a little softer for some flex. Al

As the evenings are getting shorter. I started to was the lights on the 2920 and I think they are dim. I can see the numbers but the needle is hard to see on all the gauges. Is this common on these tractors. Al

I want to build a lawn roller. Something for the 3 point hitch on the Kubota 2920. It would be nice to have the roller so it could be moved easier than the concrete ones as it would be lighter when not in used. A thought I had is to use the weight box as added weight and have the roller(s)...

I have to say that putting the MMM (60") on the new 2920 I have is quite slick. I have used the drive over deck a couple times and have turned the MMM wheels and rolled it out a couple times. Either way works well and driving over the deck has not bothered me as much as I thought it would. The...

On my new B2920 the loader will lift almost 1000lbs from its specs. I was thinking about adding pallet forks to it but at only 1000lbs lift it would be a little light. The 3 point pallet forks are not as good but will the 3 point hitch lift more or the same lift as the FEL as it is on the same...

I am looking for info and sizing for a new tractor. As the MF1020 Hydro works well I am running a little short on HP in heavy going. I cut 8 acres of grass and in the spring growing season the 1020 is working hard. Also in the winter I have 14,000 sq feet of snow to blow (over 500 foot drive...

I am looking for info and sizing for a new tractor. As the MF1020 Hydro works well I am running a little short on HP in heavy going. I cut 8 acres of grass and in the spring growing season the 1020 is working hard. Also in the winter I have 14,000 sq feet of snow to blow (over 500 foot drive...

Hello I am new to the forum and to be honest new to any forum style. I hope I will not screw up using this format with a post in the wrong place. I have a MF 1020 HST 2 wheel drive with a Ford 715A blower for the winter (Canada) and a IH -FMC 60 front mount finish mower for the 8 acres that...