Recent content by txvrod

Thanks, not sure I want to go to that extreme! Would be nice to level the land back out.

Over the years the bottom run of barb wire fence, around the hay field, has been buried by the dirt in some spots. There is a ridge of dirt just under and into the bottom row of the barb wire. I am sure this is from repeatedly cutting of the hay and working the dirt next to the fence. Any...

No input? Well guess I am the test subject. I ordered one and put it on this weekend. I ordered the: "VEVOR Shaft, 1-3/8” PTO Drive Shaft, 6 Spline Both Ends PTO Driveline Shaft, Series 4 Tractor PTO Shaft, 49”-71” Brush Hog PTO Shaft, Black PTO Shaft with Slip Clutch for Bush Hog/Finish Mower"...

Just found their site loooking for a PTO Shaft. Came here to research reviews. Anyone bought one of their PTO's? About half of one from TSC. I will be using on my Mahindra 38hp with 6 foot shredder.

I have a Freeman Coil Nailer but it is for fencing. They do make a roofing nail gun. I bought a whole set of freeman nailers when I was remodeling a house, framing, finishing, stapler, all have worked well for me. These came from Home Depot, they are not in the store but I got them Online during...

OK got it fixed! The problem was what I suspected in the first place. The 2 male connectors were reversed. I posted a picture of the hoses and the way they were connected. Now the 2 hoses that are not covered (bare) are connected. The one with the hose "sock" has a yellow zip tie, not sure what...

Using the Knob under the seat for the rate of rise and fall does nothing same for the 3 point lever on the side.

One more picture....small oak...probably one of the bigger trees I have pulled with the intimidator, would not be afraid to put it on a skid steer and push it hard, plan to do that in the future. This was right next to the fence so took some work but again no damage to the fence and no stump...

Thanks K5lwq. I have tried the control knob and nothing. I will post pics after this weekend. The tractor is 1.5 hour away and I only get there once a week. In the diagram above the #2 line is going to the valve block but right now on my tractor it is not connected to anything. This line #2 is...

I posted in the Mahindra Owners thread but wondering if any of the folks that do hydaraulics would be able to help me out. Will you click the link to that forum thread and see if you can help me out? Thanks! 1538 3 point without pressure

Got ours for $2800 in May of 2020, I spoke with Glenn Danuser, he called me within 5 minutes of an email I sent because I wasn't sure how to put it on a JD hook up. I decided to buy a Worksaver adaptor for JD to Skid Steer connector which was $700. I was looking at the Titan JD to Skid Steer but...

I have posted before and stick by it, the INTIMIDATOR is great! From small to big it will work, there is a little issue with the site over the hood (JD 5225) but it works as advertised. I have used it to dig roots on things that wouldn't just pull out. I have also used it with brush on a fence...

If I ever get this figured out I want to add 2 extra valves in the back with a 4 button joystick in the cab. Any hydraulics expert want to help me with this idea would be appreciated! I will then run lines up to the loader and be able to add a grapple. My FIL did this with his JD. The JD has the...

OK, so i got a few minutes to look at the tractor yesterday and chase the hoses. The hose in this diagram labeled 2 is a steel line that goes to a rubber line that stays disconnected when the backhoe is off of the tractor. Is this correct? the other two hoses going to the tractor that are...

The engine RPM seem to drop when I unhook the 2 that are currently able to be connected. There is fluid present when they are unhooked and the engine is running. Sorry, but I don't remember if both have fluid whe in press the center pin or not. The one remaining hose has a smaller male...