Recent content by Ole Orange

I posted this under the Kubota heading but thought I might get more response here, I did get one under the Kubota heading Thanks so heres the question well seems how there are a lot of guys and gals with way more knowledge about tractors than me perhaps they could point me in some direction...

well seems how there are a lot of guys and gals with way more knowledge about tractors than me perhaps they could point me in some direction. Hooked up the snow blower today (3 point rear mount) and noticed that the pto shaft from the tractor I believe is slowing down then speeding up while the...

Hi all, haven't posted for quite a while as everything running smooth and no questions. So that leads me to my latest purchase. I just picked up for a very cheap price a Kubota L 321 snowblower. what I know so far is it is made by McKee and is also known as a Sno-lander 320 they also made these...

Not sure whats coming but we are ready up in Maine looks like about 20+

Not really sure where to post this question but?? I have a 40 HP Kubota 3650 and the rear wheels/rims have 2 sets of mounting holes. It appears as though if I use the inner mounting holes it will space out my rear wheels about 4 to 5 inches more over all than they are now. Will this make much...

Quick question? I just installed a prince cross over valve on my loader mounted plow. When I was plowing this week end i fetched up on a rock, my trip edge tripped but pretty much stopped the tractor, I was going real slow but the cross over valve did not release trying to figure out do I adjust...

Sorry off topic but...I can try to find the part # they make a front axel vent that stops pressure in the from axel I installed one this summer and not one leak since!! Had been leaking both sides as well as drive shaft seal. You would think Kubota would let us in on these things part was $20.00...

Heres mine I went with 15 foot hoses to rear remotes for power angle, no snow yet but waiting:dance1:

Question? I am getting ready to hook 2, 16 foot hoses to my rears for control of a front plow, I bled out my plow cylinders but what should I do with the new hoses? do I hook them up dry and just run them to get air out or should I hook to the rear remotes and push fluid through until it comes...

Heres mine Plow cost me $75.00 2 angle brackets $20.00 crossover valve and hoses and quick connects $150.00 and misc. paint its now yellow. about 300 bucks

Getting ready for winter. my new add on a 7.5 ft. Fisher plow, already for yellow paint. I finished painting the bucket, the frame and plow mounts, primed the plow. Now working on new hoses to go to the rear remotes as well as a cross over cushion valve. drained the cylinders yesterday and...

I have finished mounting my 7.5 foot Fisher plow into my front bucket. (will post pics when I am done) I have good rams on my plow and am in the process of hooking the rear remotes to my to Fisher cylinders. My question is do I need to install a cushion crossover valve in this circuit? I will...

I have a 1992 Kubota 3650 with rear remotes I am trying to find the male ends that plug into the rear remotes but do not know what to ask for when I order my hoses. Is there a standard size or name for these? Any help would be greatly appreciated. Thanks:confused:

While I am trying to figure out a problem with my trailer in another post I am looking towards winter with the tractor. I have a 8 ft fisher flow I am mounting on the front of my Kubota tractor. it has 2 rams with only 1 port per ram. What I want to do is run my two hoses from my rear remotes up...

Here is what I have and what I have done so far. I have a 7000 lb equipment trailer with dual axels the axels are Dexter with fairly new brakes, bearings, and new wiring. I have tried this on a few short trips one empty, 2 loaded with my 40 hp Kubota. I have deduced that the rear hubs are...