Recent content by Eddie

I have a 2012 John Deere X740 with 60" 7 iron deck and a 2017 x750 with 54" deck. Would like to swap them. Will they fit?????

Anyone use the quick hitch from Harbor Freight? What about quality? With coupon they are $69.95 at local store. 3-Point Quick Hitch - 27-1/2" Clearance

Lens12, Do you have any drawings on this cylinder. It is from one of your PS kits. Evidently has a valve problem, works good turning right, will not assist turning left. Hydraulic shop rebuilt it but still does the same thing.

Spread 108 tons of sand on football field. Moved all of it with YM2020. Thats a lot of work in about 6 hours!!!!

Looking for knowledge on the IH 3288. Weak points, good points, general working information that can be used in making a decision to buy one. Thanks in advance

The hydraulic pump on my 2020 has started to squeel at high RPMs. It's not starving because I heard that sound when I first bought it and the screen was stopped up. This is a different sound. It only does it when the pump is not loaded. When you load it by moving the loader or 3PH it is quiet...

I have a home made spray rig for my tractor but it was hard to get in close places and spent a lot of time turning around. Came up with the idea to put one on my Zero Turn. Should be much easier to get around with. I had a toggle switch on the dash of my tractor to turn the pump on and off but...

If you are going to buy the Yanmar aftermarket Power Steering unit, don't even bother to install the hoses. Just save your time and effort and have new strong hoses made before you install it. The ones that come with it are the cheapest, no good junk that they could find. The first one lasted...

Bought 2 new toys this spring from Leinbach. This 3PH plugger aerator and a 12" moldboard plow. Both do an exellent Job!!! This aerator really does pull the plugs about 2 1/2 inches deep. I have no trouble pulling the plow 8-9 inches in the garden and the corn patch. Really does a good job.

Looking for pictures of power steering on Yanmar 180, 180D, 187 or 187 D. Need picture of the bracket where cylinder bolts to clutch housing, and where the cylinder attaches to steering arm. You can either post pictures or email them to me. Thanks

The things some people will do to try to sell a tractor:mad: :mad: :mad: 2002 Yanmar Diesel Tractor - (eBay item 110182883812 end time Oct-29-07 22:09:13 PDT) And Another!!!!! 2002 yanmar 3000 tractor and 16ft big-tex trailer - (eBay item 280165242920 end time Oct-30-07 23:06:03 PDT)

My son has 16 acres that I started bush hogging today to get ready for winter. Did it in the spring, but even without much rain the brush grows again. Picture #1 is of the brush I was cutting. Picture #2 is some of it that has been cut Picture #3 is some Alabama Kudzoo, cleaned a lot of...

Is it possible to replace the PTO shaft seal on a YM2020 without pulling the entire cluster out of the tractor? If so, How? Kicking myself for not replacing it when I replaced the rear axle seals last winter:mad: :mad: :mad: :mad:

Been looking at adding an aftermarket power steering unit to my YM2020. Have been communicating with Len Sheaffer about a unit he has which would require some modification in order to work on my tractor. Has anyone installed an aftermarket unit? If so, could you post some pictures of what has...

How about this "3 cylinder Yanmar" that has only 2 injectors:confused: :confused: :confused: eBay: Yanmar Tractor/Loader/Scraper, New Cond, 0 hours (item 300101540050 end time Apr-23-07 15:49:39 PDT)