Recent content by banjerpicker

I have 12.6 volts to my starter but nothing to my panel, no lights no nothing. I suspect the fusible link. Can some one tell me how to remove it. I tugged on it and it didn't want to come out of the white molex type connector. does that connector come apart? if so how or do I need to tug harder...

Just bought a used L4330 2007 model. Seems to have quite a lot of vibration at about 1500-1800 RPMs. It's my first HST. Is this normal? Also own L2850 and M4700. If not, someone has suggested that there could be air in Hydro lines. I have the owners manual but I see no solution to removing air...

My gearbox on my right side hydraulic lift is not working well. It is kinda grinding as I lift or lower plus it looses all the grease thru the zerk when I am lifting with it. New one from Kubota is over $500.00 even if they have them. Anyone got a suggestion on a 3rd party replacement arm...

The last three times I have tried to start my tractor the first time for the day, it is dead, no lights on dash or headlights I can tap the battery on both terminals and it will start every time for rest of the day A few months ago I checked the battery and it was a little weak but each time it...

My manual says to use a cleaning solvent to get rid of grease and dirt build up on the knotter gears etc of my baler. No brand is mentioned. Any ideas on what to use? I bought a can of spray degreased for auto engines. Can I use that? Thanks Larry

I need a front bumper or complete grill guard for M4700 to hold Kubota weights that I already have on another tractor. Any ideas? I have checked locally and a couple of salvage yards not much luck Thanks Larry

Tack was working then quit. Showing 2000 rpms then zero Any heads up on what to look for to repair Thanks

How do you guys clean the knotters and assembly. bought baler used, kinda dirty and I need to clean before I grease fittings. Looks like last person never wiped the excess grease off the fittings and now it has attracted a lot of dirt in the knotters Thanks Larry

Does anyone know if the blades on this model are held on by reverse threaded(left handed) bolts? It does not say so in the manual. I need to remove and sharpen them. Thanks Larry

Does anyone know the size of the U joint on the 269 baler's PTO shaft? I measured one inch by 3 1/8. does that sound right? When I went to TSC and AutoZone they all seemed to be metric Larry

I am trying to help a single mom get her lawn tractor running. I has an 18hp B&S engine twin. It turns over just fine but will not start. I pulled the plugs and shot starter fluid in the plug holes but it would not fire or start to run. Pulled the plugs and they were wet so I know I got fluid in...

My L2850 will not start up until I let it sit for at least 30 to 45 minutes after I have been working it hard for an hour or two. Yesterday after tedding hay for two hours it would not start until it had been sitting for 45 minutes, then it was fine. This morning it fired up right away. Each...

I bought a used M4700 and it idles at 1000 RPM. I am use to my L2850 idling about 700 to 800. I have adjusted the linkage and far as it will go to slow it down and it is bottoming out. Can I adjust the RPMs down or is that something that is factory set or must be done at the dealer. I have the...

I have a L2850 and a M4700. Both shop manuals call for using the same steering wheel puller...over $250.00(ouch!!!) from Kubota. Do you have to use one? Or cheaper models that would work from a car dealer, parts house or even a rental place? I just need some ideas to help get this wheel off so I...

I have discovered I have a short in my wiring harness underneat the dash on the left side. I have voltage to the starter and can slap on the left side of the dash and the key will allow the tractor to start.(holding the key in pre heat mode and banging on the left side will allow the panel to...