Recent content by 51allis

I'm not sure either but I would rather err on the side of caution....you know how that goes. The simpler that the tractor can be the less worries etc. because I cannot send to the dealer now for other non ecu repairs, with the emissions gone they would definitely say something etc. As for...

In my case, my tractor is a gear (synchro shuttle) and I wired from key on-power on side of switch to both the fuel pump and injection pump relay (12v side), so that when the key is turned in the on position, both are powered, then when turning to crank position it cranks engine. I also wired...

Ok I got what you are saying now, was confused a little haha. Have a good one.

Same flows? little confused, when I looked at tractordata.com, you can find the NH Boomer 4060 has a main hydraulic pump that flows 12gpm using a tuned up (more HP same engine as LS XR4046) Shibarua N844 and power steering pump that supplies 5.5gpm. The LS XR4046 has a main hydraulic pump that...

Also, if anyone reading this and my above findings on the compatibility of putting a NH Boomer 4060 hydraulic pump upgrades your LS or NH tractor with the Shibarua N844 from 8 gpm to the 12 gpm NH Boomer 4060 pump, please try and do a write up. Thanks much.

In theory....if you have manual injectors and you energize the injection pump solenoid plus the fuel pump...then engine should run until you cut power to both injection pump solenoid and electric fuel pump. Then you need to make sure you are able to put some kind of throttle. After that, I dont...

I can tell you this so far about my tractor. Got it running again, had to follow the video on youtube for using a manual throttle cable etc. and gutted the dpf filter. Removed the fuel lines to the secondary burner for the exhaust so it no longer has fuel going to it and just routed the return...

Yes the website is down. No longer offering them. So what can be done? IN my case, I have an LS XR4046 with the Shibarua 2.2L 4-cyl diesel. So I started looking for similar tractors even from New Holland (LS Mitron made some of New Holland and Case tractors too) with the SAME engine. I used...

I own a 2014 LS XR4046 and got a nice bump in power after I deleted emissions and ECU control BUT my engine has mechanical pump and injectors, it wouldn't work with electric injectors.

Sent you a PM.

To each his own I suppose but to say that a person doesn't have enough experience etc. or that flux core and rod are messy makes you look like a welding snob. Funny that you preach teaching and education but yet you discount older methods that work just fine. Stick has been around and is till...

yes because you can use .023 solid wire with C25 and it does body panels and many other thin metals just fine. Remember with gas and solid wire, DO NOT do the previous tip I gave you about wire stand out, that only applies to flux core because the farther away you hold the torch with GAS/solid...

One other tip for thin welding with flux core mig and there is some dispute but as long as its not a structural piece try this: hold the mig nozzle a little farther away from your thin metal piece. A certified welder taught me that about 10 years ago, what happens is that the farther the wire...

I gave my son my Hobart 140 mig, biggest mistake I ever made hahaha. But that welder will go down to 22 amps and can weld some thin steel with solid wire and C25 gas, but then you have to have the gas. However, it also welds with flux core .030 you can turn it all the way down and practice...

"A welding course would be good" VERY true. 30 years ago, my rural area schools offered "adult community education" courses (utilizing intermediate school welding lab), welding was one of them. Took the course for $35 for a full school year at night. The best thing I ever did was learn to weld...