Yesterday Iron.

   / Yesterday Iron. #1  

Thomas

Epic Contributor
Joined
Apr 6, 2000
Messages
31,030
Location
Lebanon,NH.
Tractor
Kubota B2650HSD w/Frontloader & CC LTX1046 & Craftman T2200 lawn mower.
Taken at Deerfield,NH fair 06.
 
Last edited:
   / Yesterday Iron. #2  
I didn't get much time to mull around the old iron, but I did enjoy that Bear. At the tractor pull friday night there where two beautiful Cockshutt's.
 
   / Yesterday Iron.
  • Thread Starter
#3  
Afternoon pekabu.
I saw one of the Cockshutt's pull (one nice looking clean machine) I must been getting refill of chicken stew in the bread...got a tad chilly setting while watching.
Wish they would hold the pulls on Saturday...makes long day if you have to be at work before sunrise.
 
   / Yesterday Iron. #4  
I believe they did have some Saturday starting at 10:00. Not positive. It was a bit chilly, but the McCormick MC120 was pretty comfy. :D
 
   / Yesterday Iron.
  • Thread Starter
#6  
pekabu said:
but the McCormick MC120 was pretty comfy. :D

Dave,were you the lucky one hitching up to the sled to pull back each time??...I'll say the other McCormick wasn't shabby either. :)
 
   / Yesterday Iron.
  • Thread Starter
#7  
Egon said:
Thanks for the pictures Thomas.:D

How ya been...hope that nasty low pressure didn't dump to much rain on you folks....your welcome Sir.:)
 
   / Yesterday Iron. #8  
Yes, my son and I finished the night. My left leg was killing me though. I guess they are working on a self propelled unit. Maybe next year. I was checking out the sled and it was an interesting piece of machinary. I can't remember if it was two or three 4 speed trannys', hooked up to a Transfer case, and then a two speed rear end. Air over Hydraulic brakes on the box.

Wasn't the easiest job. At the end of the track I had to push the clutch, yank the rope to disengage the pintle, then dump the clutch so the sled wouldn't hit me. Didn't always work. Backing into the sled if you weren't dead on forget it. Funny thing though, the farther the sled went the harder it was to get going. It really dug in.
 
   / Yesterday Iron.
  • Thread Starter
#9  
pekabu said:
Backing into the sled if you weren't dead on forget it. Funny thing though, the farther the sled went the harder it was to get going. It really dug in.

Well than you did pretty darn good hitching up,for I notice very times you didn't hitch the first try...even w/the bad lighting.

Wonder if the pulling tractors loosen up the ground which made it little tougher for you to get traction pulling back the sled...hmmm.

Next year I plan on setting up high w/heavier coat and themos of hot coffee.
 
   / Yesterday Iron. #10  
Thanks. Hopefully less rain. Friday wasn't too bad people wise, but Thursday and Saturday were murder. People were running out of gas waiting to get out! We'll have to try and meet next year.

One feature I love on the bigger tractors is the gear splitter. On the CX's I believe there is a high low, and the MC there is 3 or 4 splits. So I was in 2nd, but started out in 2/1, then without having to let off the gas you slide the button up and it shifts into 2/2, then 2/3... . Not as easy as a hydro but sweet none the less.
 

Tractor & Equipment Auctions

2013 INTERNATIONAL WORKSTAR 7600 SBA 6X4 DUMP TRK (A51406)
2013 INTERNATIONAL...
2020 John Deere 870GP Articulated Motor Grader (A49461)
2020 John Deere...
2020 KUBOTA RTV X1100C UTV (A51406)
2020 KUBOTA RTV...
2020 John Deere 3032E Tractor Loader Backhoe (A51243)
2020 John Deere...
WITTIG VACUUM PUMP (A50854)
WITTIG VACUUM PUMP...
Target Econline 2 Concrete Saw (A49461)
Target Econline 2...
 
Top