lift arms

My 2015 Mahindra 5555 rear lift arms, when under a load, will only lift by bumping the FEL joystick. This began after removing a PHD and running the tractor, lift arms up, with no rear attachment. We normally have a box blade mounted but left it off for a while when we were using a root...

Hey everyone, new to international tractors. I just recently purchased a international 574. It's been sitting for a few years but everything works. My question is, everything I've read says it should have category 2 ball ends. Mine has cat 1. For curiosity, I took it off and the other end, the...

Hello everyone, I recently bought a SAME Minitauro 60 tractor and have done a lot of restoration on it, but I'm having some problems with the hydraulics and lift arms, and I’d really appreciate any advice or insight. The issue is with the two control levers located near the steering wheel...

Hello. I have a Mahindra 4110 tractor that suddenly stopped lifting the 3-point hitch arms. I have found that the Position lever is attached to Nothing under the tractor! I have attached 2 pictures, one that shows the rear, right side of the tractor looking where the right lift arm would be and...

It is no longer winter, so I went about putting the blowers and blades out of the way on pallets. I took the opportunity to install the Pat's adapters to the Kubota B2601 as the extra length is needed when the MacKissic chipper/ shredder is fitted, matching length to the other two tractors...

Hello everyone, I have been gone for some time from the forum and of course I come back needing help. I traded my 19 year old B3030 for a new LX4020 this summer. This weekend I took off my 72" MMM to put the loader and land pride plow on. I have read the manual a thousand times and can not...

Hello, has anyone replaced there non-teloscoping lift arms with telescoping lift arms on their 3 pt. for a 1971 Ford 3000 tractor. If so what part number or what tractor telescoping lift arms will work. It is really cumbersome to cool up a heavy 3 pt. attachment. It looks like just maybe the...

I have a 1971 Ford 3000 tractor with original 971 hours. I have owned in since 1998 and has had a 3 pt lift arm issue since then. I recently installed a 2 spool hydraulic valve to operate the hydraulic bar lift on my new Enorossi sickle bar mower. After sitting for a few weeks the spool valve...

What do you use those Kubota loader arm thru-holes for? Here's what lives in ours. Shovel, hoe, hook, rock bar, and a cheater pipe for the SSQA levers. Still room for one more something... A single bungy around the hoe holds it all in place. rScotty.

Seems the lift arms on my TC35D want to float up too easily. Pulling a small sod buster plow i find it almost impossible to keep sufficient pressure to keep it in the ground to work. Have tried various pitch on ripper and blade to no avail. I have to stop about every 20 feet and cycle the...

The lift arms will not go up .I bought this tractor used they never have worked they tapped in to the hydraulics to add a front end loader I took the loader off and just used use the tractor. Does any body have an answer to why the lift arms will not work.

This is a weird one; our x590 has never had a serious problem. But I had to take the mowing deck off tonight to reinstall the belt, which had come off one of the rollers. Something seemed strange, though; the deck wasn't going all the way down to the ground....wt...?. I did get the deck off with...

I need to put some stabilizers on my lift arms, because I had the frame of my 3pt dump bucket catching on the treads of my tire, and I really do not want to have to replace a tractor tire unnecessarily. what do you use, and why do you prefer it? thank you for any advice or tips!

1962 Case 430 The lift arms are somewhat splayed, and so the ends are just a wee bit wide for hooking up without having to pull them together with a ratchet tie-down and some “easing” with a ball-pein to hook up attachments, which pretty much defeats the whole idea of the Eagle Claw “QUICK”...

1Already tried the speed drop knob ✔️ 2Already checked the draft ✔️ 3Already checked the rear hydr lever- position in neutr ✔️ 4Already checked tran/Hydr levels✔️ 5Already tapped the arms w a tiny sledge 3# ✔️ 6Pulled the seat to find there is no access to linkage from there :( Fel & grapple...

I am making a bed lifter implement and would like to talk about pin length for lower (or upper) arms of 3pt attachment. Take a look at these to examples. The important dimension is B. It is 5in(~130mm) in second image and 3 3/4in(~95mm) in the third. Since this is for category 2 tractor, I...

The lift arms and tilt lock up on my 2015 Compact Tracked Loader after 15 - 30 minutes of operation while using a bucket or auger attachment. The only fault code displayed is M3507 (Hydraulic fan open circuit), usually displaying after 2 - 5 minutes of operation. The fan is turning and the...

The lift arms and tilt lock up on my 2015 Compact Tracked Loader after 15 - 30 minutes of operation while using a bucket or auger attachment. The only fault code displayed is M3507 (Hydraulic fan open circuit), usually displaying after 2 - 5 minutes of operation. The fan is turning and the...