kubota zd326

Have a ZD326, 445 Hours. Noticed that the fuel gauge was not working. Temp gauge not working either. Pulled the Left Tank fuel sensor, no corrosion or obvious problems. Float seemed sound. Connection terminal and ground seemed OK. Any idea if these fuel sensors (K3181-62150) ever short out...

I was cutting grass when it suddenly killed. It starts fine but if I move either handle to make it go it kills in a couple of seconds. It only runs with the handles fully extended apart. Another thing I noticed: It will now start without pushing down on the brake pedal and the brake pedal feels...

My ZD326 was laid up for a couple of weeks while I repaired the fuel gauge and with the hot weather and lots of rain we have been having my grass grew rapidly and was a lot higher and thicker than usual. I also have a mulcher on it which makes it even harder to cut tall grass. I bought 2 new cup...

My main gas gauge on my ZD326 stopped working and stays all the way down on empty. I suppose the float in the tank is at fault. How hard is this to repair or replace?

I'm not paying $250 for a Kubota battery. Who knows of a good replacement battery that will fit in a zd326. My original battery is 9"Length, 4 5/8" Wide and 8 3/4" High. 475 CCA.

Ordered three gator blades for my 60” ZD326. I wanted these blades for mulching leafs with my vacuum. Blades are exactly the same size,width as original Kubota blades, except thickness is less. I tried installing,everything fit perfectly but blades will not tighten up. They feel tight but when...

I have a Kubota zd326. One day the wife went to mow, it would not start. I was kind of busy so I just crossed the starter and got it going. A couple hours later after she was done it wouldn't shut off. So I hopped on it, engaged the blades and got off the seat. It kept running. Finally just...

I have had to winch my ZD326 out of the mud a few times. Is there anything I can/should do to make it safer and/or easier? My old lawn tractors had a lever to release the hydrostatic transmission and allow free turning of the wheels. Is there anything like that on the ZDs? Th-Advance-anks

What's the differences other than cost? The reason I ask is I have a zg327 and going to upgrade to one of these this spring. Looking for suggestions, thanks!

ZD326P Issues began when the mower wouldn't shut off. Used the manual fuel shut off to stop the mower. Went to mow a few days later and the instrument panel was working (guages) and the fuel pump was energized. ' When the key was turned the glow plug light came on, but the starter never...

I recently added a Grammer MSG75 Low Profile air suspension seat to my ZD326 zero turn mower. I did a blog and added some photos showing the process. Quest for a better Zero Turn Kubota ZD326-6P Modifications Divergent Stuff Bottom line is that it's giving me a lot smoother ride on rough...

I need to get some mulching blades for my 60" ZD326. Where's the best place to get them? Thanks!

Anyone heard of someone swapping out the rear discharge deck on the ZD 326 for a normal side discharge? My love fest for my rear discharge is over. I can't handle live oak leaves not being mulched up somewhat or the stopping every hour and a half to clean the radiator screen and air filter. I'm...

Did the factory lights option for a ZD326 come with a light switch? I don't see one listed in the parts diagram. I'm adding some lights to our mower and don't see a good place to put a switch that isn't going to look out of place.

Help lol, 400 HR service removed transmission plug and both rear axle gear case plugs. Drain oil. Changed both filters. Replaced plugs. Manual says to pour fluid slowly. Manuals says 18.8 qrts. I've managed to get approx 12 qrts and I'm full to top. What's going on?

I am planning on purchasing a 2013 Kubota ZD326 zero turn diesel mower next week. Please let me know any negative or positive experiences or issues I should be made aware of on this model. It is used with 900 hours on the clock. I read all of the other forums and most reviews are positive other...

Howdy ya'll Thought you may like my video of the ZD326 front jack feature. Sure makes accessing the mower deck easy! Really sturdy too. Just let me know if you have any questions! https://youtu.be/pj4gLB0nXe8

Like the thread title states: My ZD runs fine off the left tank but not the right. I can literally turn the engine on and off simply by switching from one tank to the other. And I just filled both tanks! :banghead: So, I *assume* that the intake for the right tank is clogged or stopped up...

My old JD LT-133 finally crapped the bed after +17 years of mostly faithful service. Had no choice but to move to replace it on an accelerated timeline (I planned to do it this fall when a lot of mowers go on sale - oh well). The local craigslist was pretty bad, the only decent Kubota I could...

I bought a new ZD326 60" with a mulching kit. Naturally, you have to mow a little slower with a mulching kit since the grass is getting mulched under the mower instead of just being thrown out. So far I am very satisfied with my mower but with our heat and heavy rains in south Louisiana the...

The property I mow with these is mostly level 4 acres of rental property with multiple structures and some open field areas. I've used the F2680e for 6 years and the ZD326 for 2 1/2 hours. Will take less time next time. The Z is quicker/more manuverable between units but slower in open areas...

Has anybody installed Carlisle AT101s on a Kubota ZD326 or equivalent? The AT101s have a great reputation and I would have done it already but they are technically the wrong size at 24x12-12 while the stock tires are supposed to be (havent confirmed on my particular machine) 26x12-12. Im...

I asked about this last summer and will post this as a follow up post. We went from a Cub Cadet ZTR with lugged tires to a ZD326 with turf tires and were greatly disappointed in how well it got around but I was concerned with the weight of the ZD and lugged tires causing turf damage. I ordered...

Thought you all may enjoy my walk around vid of the Kubota ZD326. If you have any questions about the machine feel free to ask. https://youtu.be/DOYVLzbxeEg

I'll be due for a change in UDT fluid this year, probably towards eoy. This system it appears has two filters on the same system? HST filter and the hydraulic filter. Anyone know why there are two separate filters, since that is all tied together.

Hello, I have a Kubota ZD326, and its deck will not raise. It was completely fine the last time I used it, I started it about a month ago because of the deep freeze, took it outside and drove it through the snow and it was great. Now that Spring is here I have went back to it to start it and get...

Yesterday I learned that Kubota is introducing the B2601 in 2015. Looks like a nice tractor with new improved ergos. I'm considering trading in my ZD326 for one. My ZD326 is a 2014 model with around 75 hours on it. Runs great. But I'm not in love with it. It's a 60 inch cut and really...

Our ZD326 with 60" deck needs new blades and I'm leaning towards a set of Gator G6 blades but am open to suggestions if there's something better. Don't really need aggressive mulching but something that would chop up tall grass a little bit better would be nice.

Looking to find out what new ZD366 60 inch side discharge mowers are going for

is there a remote chance anyone can scan the page out of their manual and post it on how to level the deck on a 326? i have spent hours trying to adjust the thing and cant get a straight cut. i have measured the deck, measured the blades, added "rake" the the deck just about everything i can...

Other than constantly watching the tube, how do you know to empty before it gets clogged?

Have seen this issue described in the past but never with a final solution. Need to know how to fix this problem. Called the Kubota dealer and they said they never heard of such a thing. ZD 326 200hr. D1005 engine. Maintained. Engine stopped while in use. Now, key ON position results in...

Case in point; 5yr old zero turn ZD326(26hp diesel). I'm having cold starting issues. Starter bendix will click but starter will not engage unless I try starting multiple times. I've tried two batteries. My fixed load battery tester(130A) shows "good" with a 15sec test load. Clean connections...

Hello, Saw on Kubota website that a new 2014 ZD326 is coming out. Anyone have any details on this new machine? I'm in the market for a ZD326 in the next few months. Thanks!

Considering trying a Kubota ZD326 or ZD331 with 60" rear discharge deck and was wondering if the cut grass gets under the ZD326 or ZD331. Do you Z owners have issues with cut grass packing under the machine, not the deck, but on/around the undercarriage?

I just picked up a mint condition 2010 ZD326 60" side discharge with 122 hours. I mowed today after about 2 weeks off (was on vacation!) and cut 2-2.5" off of 5" tall grass. The mower handled this with ease but left some serious windrows! My last mower was a Gravely 152Z 52" deck and factory...

About a year ago i was mowing at little to fast and hit a small stump back on my trails, when I hit it the motor flexed in the mounts and caused somethig to hit the radiator twords the bottom and knock a hole in it. years of auto repair i knew where to take it for repair, unfortunatly they were...

I have a ZD326 and the deck will raise up so you can adjust the height of the cut I want but will only go part of the way back down. No arms seen to be bent so the only thing I can think of is the hydraulic cyclinder. Any suggestions?

I just added led lights to my L5240 and it was a piece of cake. My 5240 had a harness behind the seat to tie in to. I'm about to add led's to my ZD326 and was wondering if it has a harness as well. I did look in the fuse box and there is a space for a 20 amp fuse for a work light. Have any of...

I致e had this ZD326 for a couple of years, and when I bought it, I thought what a silly arrangement they have on their fuel gauges. There are two separate tanks, left and right. A switch below the seat allows you to pull fuel from either one, or turn the fuel totally off. Each tank has a...

I posted this in the lawn and garden but only received 2 responses so I'm trying here. I probably should have posted here first since it is about buying. I'm looking to buy a Z this month because of the rebates. I'm can't make up my mind between the two. I will be cutting 3.5 ac every week and 5...

Good morning, I have a Kubota ZD326 mower, with 60" deck. I mow about five acres of grass/weeds. The machine works great for my needs and has good fuel usage. I try to do my own service , oil changes , filters and lub. At 270 hours I replaced the two fuel filters, after removing the battery...

Hi, Does anyone out there have a zd 326 or 331 with say over 1500 hrs on it. I would like to know if they are holding up well especially the ones with the 60 inch dedicated mulching deck. cheers.

Has anyone explored options for more rear tire traction? Turf-savers are ok, but sometimes sure lack decent traction. I suppose the heavy weight of the machine doesn't help either. I remember seeing a shallow cup design some years ago on the Grasshopper machines that may afford more traction...

Can the inner air filter be washed? It looks as if it's made from synthetic media which should tolerate a mild cleaning with soap and water.

What would cause a rear main oil seal to all of a sudden start to leak on a ZD326 with 400hrs? It has been about 60hrs since the last oil change and I make frequent checks on all fluid levels. Today I noticed a wet spot on the garage floor behind the mower and found oil on the frame under the...

I saw a Kubota 326 that had bolt on rear splash sheilds,they were on a new Kubota,they were bolted under each fuel tank and extend out, has anyone seen these. I'm guessing they prevent mud from flying up and may even protect the fuel tanks. I'm looking for the part number. Thanks Ken

After about a year of thinking and procrastinating the new ZTR is finally on it's way. The dealer got it in yesterday and is servicing it today and will deliver tomorrow. We've finally gotten a little rain in the last few days so I may actually have some grass to cut with it as well. He's...

I am thinking of putting the 326 for sale and going back to a tractor. Any thoughts on the value appreciated. 2007 with 212 hrs. Great shape

I purchased a new ZD326 a couple of weeks ago and unfortunately my deck was not level from the dealer. It was about 1/2" higher on one side than the other. I check the level on a very flat and level surface and I also verified that all of my tire pressures were correct. I successfully...

Does anyone know if you could use ATV tires on a zero turn mower for increased traction? My ZD326 is terrible with the stock turf tires on it. They are 26x12-12 and I've found some ATV tires this size and wonder if they would work? Any help would be greatly appreciated. Thanks

I had purchased a B2920 with a 60" MMM but I held off a little bit unsure about my real needs. Dealer has been very understanding and has not pressured me at all with anything. They have even let me demo a few things before I make this purchase. I have a JD 737 zero turn now 54" deck 23HP gas...

Hi all, I made my decision - It will be a NEW Kubota ZD326 w/ 60" deck Now it's down to getting the best price I can Wondering what others have paid or been quoted for this wonderful machine

The manual says either one. I have UDT for tractors etc, but not SUDT which I know is more expensive. Does either work ok, or is this hst happier with SUDT? What is everyone else using?

I have a Kubota ZD 326, and I have a problem that I hope someone can help with. My engine, after running awhile will overheat, the temperature guage moves into the red zone, and then emits a high pitched noise, at which time I immediately kill the motor. This has been reported to the dealer...

Finally the new Kubota I ordered has arrived at my local dealer. I can't wait to get it, even thou theres 2ft of snow still out on the yard, its still exciting! I traded this up from my '98 kubota GF1800 2wd Also just a FYI to everyone looking into buying a new kubota anytime soon, My friend at...

Anyone had the displeasure of changing the tranny oil yet? After about 2 hrs and 2.5 gals later, I finally got it! It takes time for the oil to fill all those small passages in the HST. What a pain!

Received this responce from Customer Satisfaction@Kubota.com Dear Sir: The differences you mentioned below are the only ones between the two models. The engines are the same and the transmissions are the same. However, the gear ratio is reduced on the ZD326S to match that of the ZD321, that is...

I have been looking at the new Kubota 326 pro with the 26hp diesel engine with 60 inch cut and the Ferris 4500 model with the 28Hp cat.diesel 61 inch cut.I have been told by the sales people to stay with the twin hydro and two wheel motors on the ferris.How does the Kubota 326 pro stack up...

just wanted to post some pics of my new zd326 Yahoo! Photos - workinallthetime's Photos - kubota bx23 2005 model this thing seems to be a monster yet it is much more quiet than my bx23. the workmanship is great and i actually did a little mowing with it as soon as i got it off the trailer...

11,400 here in tulsa for the zd326 w/ 60" deck i was told no 0% for more than 12 months and no rebates w/ 0% that thing looks like a monster !!!!! ohh and i was also quoted 12,500 for the ferris with a cat diesel and 12,500 for that ugly green thing with a diesl in it i think its called a john...