john deere 4610

I am requesting someone in the Northern California area near Auburn allow me to compare one or two items on your tractor with mine. My tractor was disassembled and I am trying to piece it back together. I didnt disassemble it, I just own the tractor and Im trying to get it up and running again...

I bought a used 4610 while deployed overseas, my handyman back in the states ended up blowing the engine (connecting rod thru the crankcase) Long story short when I returned home two years later the tractor was in pieces, I had the engine completely rebuilt, Ive been trying to piece it all back...

I was stationed overseas for 4 years, meanwhile a handy man hired to maintain my property back in the states, blew the engine in my JD 4610. When I returned home I found it completely disassembled and I'm trying to put it all back together. There are a few points I'm stuck on, as I can't...

What year was my tractor Serial number LV4610H260528

So today I let my neighbor use my JD 4610 tractor to pull some junk out of the woods, and for some reason half way through the job the tilt function on the JD 460 loader quit working. I checked the usual suspects (loose QC fittings, blown hose, hydraulic level), and can not find any obvious...

Hi, I have the chance to pick up a nice John Deere 4610 for sale. I see this tractor was only produced for a couple years before the 20 series was produced. Any concerns over a ten series vs a twenty series? Since the 4610 was only produced for two years, I'm not able to find much data on how...

I was bushogging on my property yesterday and saw hydraulic fluid coming from underneath the tractor. Shut off the bushhog and made it back to my barn. When I got there I had lost quite a bit of fluid and I saw that the manifold on the transmission suction line and implement pump line had gotten...

How do I adjust the throttle tension? The throttle moves from desired rpm to idle when operating.

I recently bought a grapple bucket for my 2004 JD 4610. My hydraulic manifold has 7 ports. 4 are for the dual function loader (up, down, dump, curl), two are capped off, and on goes to the 3 point hitch. Here are a few pics So JD has a part that uses the two capped hydraulic ports and...

When I start my JD 4610, I have a honking noise coming from the left side of the tractor next to the hydraulic filter. Operationally, everything seems fine. No leaks. I did not run over a chicken or duck. But it feels like a pump is going. Any help appreciated. I'd rather fix it myself than...

I have a JD 4610 PowerReverser/Diesel/RearPTO. When I turn the key, it just clicks, does not start. Knowns: a) Starter Motor and engine work (we jumped the starter and fired right up); died in gear b) Battery charged. c) Plenty of diesel Tries: a) replaced all fuses b) replaced Diode Blocks...

Can someone tell me what it means when my code light flashes; short , short, long, short. Everything seems fine but this flashing bothers me. Thanks in advance.

Tilt wheel will no longer lock in place and just flops, what is broken and how difficult is it to repair? Dennis J

I was scraping off a concrete parking lot today had about 6" of silt run off on it hit a new section of concrete and loader frame hopped off the mount and came up in the seat with me backed up and relocked it in place and finished the job had this happed one time while pushin up a burn pile...

Hello and happy Friday to all. My JD 4610 has a weird problem. If I operated the rear HYD for a while, say scraping or mowing, or any condition that requires the selector switch to be set for rear HYD, when I change back to front for bucket loader work the bucket won't go up or down. It grunts...

my 4610 4WD with power reverser has been sitting since late summer and I went to do some work and at first the hydraulics were erratic. This has blossumed to no motion in forward or reverse, no hydraulic (spastic intermittant action at best) and I have change both filters to no avail. Any ideas...

I own a JD 4610 Tractor and I want to pull a Case IH 8420 Round baler with it ... according to tractor and baler specs I am ok. But the owner of the baler is telling me my tractors hydraulic system cant handle it and the gate will not stay shut during the final stages of bale compression. Does...

I'm considering purchase of a used 2004 John Deere 4610 4x4 from a private party. They are asking $25K and I'm wondering if this is a reasonable price. Here's the specs and included implements: - 1800 Hours - Shuttle-shift transmission (I was hoping to find HST, so also wondering how well...

Looking for some help on a 3PT issue. I have a 2003 JD 4610. When I move the 3PT lever to the full up position the hydraulic pump does not release and places a continuous load on the engine. When the 3PT lever is moved approximately 1 inch forward of the full up position the pump will release...

I am considering buying a 2004 diesel 4610 with 400 hours, hydraulic mid and rear pto, post hole digger, bucket, blade and brush cutter - asking price is $22,000. Can you tell me if this is a good deal or not? I plan on using it for general maintenance on a horse farm.

I have a JD 4610. I had a electric diverter valve installed to operate my top tilt on my on my boxblade. Today, the wiring from the diverter switch got caught in some brush and tore the wiring into and blew a fuse at the same time. The tractor died immediately. I repaired the wiring and replaced...

I have a JD 4610. I had a electric diverter valve installed to operate my top tilt on my on my boxblade. Today, the wiring from the diverter switch got caught in some brush and tore the wiring into and blew a fuse at the same time. The tractor died immediately. I repaired the wiring and replaced...

We are trying to decide what the best tractor for us is. We want to have an all purpose tractor that is not too bulky to get around the barn that also can mow the pastures a few times during the summer. We have about 15 acres of pasture that is hilly with some slopes that approach a 30% grade...

Ok, folks, let's try not to start a brand war...:-) I am about to purchase either a TC40DA or a John Deere 4610. I already own a TC29D with Supersteer a FEL and approx. 550 hours on it. It's been a good machine, but to small to move round bales so I need to get a larger chassis machine with...

I'm trying to help my dad help spend some of his hard earned cash, and he wants either a Kubota L4330 or a JD 4610. I'd like to hear from anyone who has knowledge or experience with either one of these machines. With either one he wants a shuttle shift manual transmission (not hydro), loader...

Does anyone know of a good price on a 4610 with shuttle shift (not eHydro), JD 460 loader with HD bucket, and either a Bradco 408 or JD 48 backhoe?

Well I was all set to go ahead and order my TC40D today, but at the last minute thought I would give the local Deere dealer a shot at my business Deere: 4610 e-hydro, 460 Loader w/4n1 bucket / 48 backhoe rear remote, block heater, girll guard, QT bucket, arm-rests LIST: $38,726 SALE: $30,118...

OK the neighbor is looking at hydro CUTs. He does not like the pedal on the Kubota,so it is scratched from his list. The local CIH dealer sells Kubotas,so he does not sell the DX. The local MF and Agco dealers are way too high on price. The TCD with loader is priced at $35,000 CDN for a brand...

I was wondering if anyone out there might shed some light on how long it usually takes to take delivery on a tractor after it is ordered? My father and I ordered the 4610 the first week of Oct. it is now Dec. 5th and still no tractor. The dealer said it was invoiced on the 25th of Nov. The wait...

I am in the market for a jd 4610 with factory loader and ehydro feature. I am having trouble finding good info on reasonable price. How much barginning can I do with the dealer. Also trading in a ford 1500 with 770 loader - any idea of good trade-in value? Thanks, Mike

I'm interested in a JD 46XX series HYDROSTATIC tractor. Is it worth waiting for the 4610 instead of the 4600? Thanks, John in SC