Search results

Results 1 to 15 of 15
  1. G

    SC2400 (aka EA2400) stopped dead

    Thanks for that diagram, big help. I went back to the start and retraced my footsteps and lo and behold I find the 5A PTO fuse blown in the panel, I’m sure I checked that, but it just shows… some people should double check more than others🙄
  2. G

    SC2400 (aka EA2400) stopped dead

    Thanks, I’ll double check that as that’d be a preferred cause!
  3. G

    SC2400 (aka EA2400) stopped dead

    Yes, all good
  4. G

    SC2400 (aka EA2400) stopped dead

    Yeah first thing I checked.
  5. G

    SC2400 (aka EA2400) stopped dead

    Yeah sorry forgot to mention all fuses ok.
  6. G

    SC2400 (aka EA2400) stopped dead

    Hey everyone. While mowing with my EA/SC 2400 (Yanmar/CC) it just stopped suddenly, dead. Wont even try turn over at all. Some very amateur investigation later it appears no power getting to starter motor on key turn. Can’t find any wiring diagram help for this model, but I’m guessing a...
  7. G

    SC 2400 problems/advice

    Thanks, something to keep in mind. I've pulled out the shaft and am getting the uni join replaced. It was flogged out majorily, so likely and hopefully the cause of my noise in 4wd. The other tractor had not had the pin whacked through the spline properly and has flogged out the other side of...
  8. G

    SC 2400 problems/advice

    Reason found for stopping dead while mowing with MMM, and then not even turning over was PTO fuse. Hopefully just a worn out fuse and nothing more sinister.
  9. G

    EA 2400 problems/advice

    Yeah that was the first thing I checked. In the manual, showing how to change the front axle gear oil, there is no mention of what looks like little bleeder type valves on area where I could imagine air being trapped when refilling with oil. I do not recall using this when i changed out axle...
  10. G

    SC 2400 problems/advice

    Is it possible for the uni joints (?) of the front diff (propellor) shaft to be that whacked out and loose that they can make a noise when engaged? Both tractors front wheels when lifted and turned sound similar, not grindy at all actually. I'm hopeful all those front end sounds are coming...
  11. G

    EA 2400 problems/advice

    Ahoy everybody. Have had a EA2400 Yanmar (same as SC2400 CubCadet, have also posted this in CC thread) over here in Australia for a long time. It's been awesome. Mistreated the front axle with the FEL on hills with no back ballast a few too many times and it has started to make a bit of noise...
  12. G

    SC 2400 problems/advice

    Ahoy everybody. Have had a EA2400 Yanmar (same as SC2400 CC) over here in Australia for a long time. It's been awesome. Mistreated the front axle with the FEL on hills with no back ballast a few too many times and it has started to make a bit of noise somewhere up front only when 4wd is...
  13. G

    Buying Advice  Best MMM performance/bigger tractor

    Hello. Appreciate any feedback on CUTs with regards to mainly mowing performance and good stability on hills. Anything much over a tonne is probably getting on the too big side. Was sold on a Yanmar EA2400(CC SC2400 in USA) but thinking I don't want to make the mistake of going to small. I have...
  14. G

    Buying a new Yanmar 2400 SCUT but...

    All but sold on a Yanmar EA2400(CC SC2400 in the old US of A). Main jobs are mowing (so require MMM) and light FEL work. From all reports this tractor does these things well and they are nicely priced over here. I'm in the hills so stability is important and this appears ok. My last hurdle...
  15. G

    Buying Advice  new Iseki TH 4365

    Hey people. My first post. A new model Iseki has come out, the TH 4365. I'm in the market for a new small tractor that needs to have a loader and a mmm. I realise I'm looking at two different animals here but I was all but sold on the Yanmar EA 2400 (Cub Cadet GC 2400 in your land). Most...
Top