Search results

Results 1 to 24 of 24
  1. M

    People with rotary 3 point spreaders... does your tractor ever get corrosion issues?

    I have to clean everything (spreader/tractor) after spreading lime, and or fertilizer. Or else corrosion starts. Better to clean, than fight corrosion.
  2. M

    20 inch chainsaw recommendation

    I have the Echo 590 Timber wolf. Great saw.
  3. M

    Best and worst chainsaw?

    Another happy Echo CS 590 Timberwolf owner/user. I love this saw.
  4. M

    Help with an oil change Farmtrac 550DTC

    I ended up putting in ten quarts. I’ll run a while and recheck. Thanks for your help
  5. M

    Help with an oil change Farmtrac 550DTC

    Thanks Willy. I put 8 quarts in with a new filter, and it’s not even half way between the low and high. That’s why I’m confused. I don’t want to over or under fill it. When I drained it, I measured as best I could what came out at almost 9 quarts. Before draining, I check the oil level and...
  6. M

    Help with an oil change Farmtrac 550DTC

    I have a 2006 Farmtrac 550DTC tractor, it’s the Korean made by LS model, not the Farmtrac that looks like a Ford. It’s has a 4 cylinder Mitsubishi Diesel. I hope I can attach the photos from the top of the engine. Here’s where I need help, I can’t locate my manuals for it. I don’t recall the...
  7. M

    Online source for Kioti parts ?

    thank you!
  8. M

    Online source for Kioti parts ?

    Thank you very much!!
  9. M

    Online source for Kioti parts ?

    Hi Anyone know of an online Kioti parts dealer? Dealer I bought my Kioti stocks few parts. Other than Kioti oil and fuel filters he has to order parts for me. Besides the time delay, I get charged the shipping and handling to his dealership location, then add on several hours of my time to...
  10. M

    Gifted a Tractor... need help

    OP, any updates for us? Thank you
  11. M

    Bought a New L3902, turned out to be a 2019

    Inquiring minds want to know!
  12. M

    Disc axle nut tightness

    They are 1 7/16” nuts, the axles are 1” square. Since I felt the axles should spin freely like a roulette wheel, I was concerned I might have over tightened the nuts. I’m glad to hear that being very tight is the correct way. The axles spin, but only as I turn them. I imagine as others...
  13. M

    Disc axle nut tightness

    Thanks Ken. I was concerned about over tightening, thinking I could somehow stress, or impede the bearings. The axles each have a nut, and then a nylock(sp?) nut. I bought new Nylocks. After I use it a bit, I’ll check tightness, and snug the new ones on it. Thanks for your help
  14. M

    Disc axle nut tightness

    Thank you very much! I appreciate your advice.
  15. M

    Disc axle nut tightness

    Thank you very much. All 4 gangs spins, the rear two spin easier(freer) than the front two spin, but none are like spinning a something lubed. No noise, or bad bearing sounds. In other words I can turn them by hand, but not give them a spin, and they keep turning a while. I’m assuming that’s...
  16. M

    Kubota Possible Purchase

    I have both. Anything in the future will be 4wd
  17. M

    Disc axle nut tightness

    Hi. I recently bought a used CountyLine (Tractor Supply) 7 foot Three point hitch disc. Three of of the disc plates were broken, so I removed the axle nut and jam nut off of two axles, and replaced them. I used my Rigid 18 volt impact gun, to tighten the 1 7/16” nuts on. I don’t have...
  18. M

    Suggestions on 20” pro saw

    I’ve had an Echo Timber Wolf 59cc, 20 inch bar For years. Came with 5 year homeowner full Warranty. Use it a lot, plenty of power, always starts. Quality saw.
  19. M

    Backhoe problem

    Please keep us updated with this. Interesting thread, sorry you have to deal with this, I hope TYM sorts it out for you.
  20. M

    Warnings on new Kubota

    Regen works, but I have to adapt to it in my M6060. I grew up running old iron, and never needed to run the high RPM to accomplish the tasks. The newer equipment needs to run at higher RPM, to get the HP and the DPF clean as others have mentioned. Years of conditioning of not having the RPMs...
  21. M

    john deere 3320 removing an in line hydraulic filter

    Thanks. Finally got it off. But could not get the filter out of the housing. Manual doesn't show the separate parts of this cleanable filter and housin. Went to John Deere dealer and had to buy the entire assembly, plus separately the o rings. $100 dollars later, after another $300 in fluid...
  22. M

    3320/50/70....changing Inline Hydraulic Filter

    I have the same problem On my 3203. Can’t get it apart. Manual is vague.
  23. M

    john deere 3320 removing an in line hydraulic filter

    Old thread…. Did you figure it out? I’m stuck. Mine is one a 3203.
  24. M

    Help with a Bush Hog th440 - need manual

    Hi anyone know how to get the CVT metal cover off of a Bush Hog TH440, after removing the bolts. no clearance between frame and the cover. I'm trying to locate a shop or service manual, no luck. Bet there is a trick to doing it. I have a rattle inside the cover and I want to take it off, to see...
Top