Search results

The broken bolt came from the hole directly below where the new bolt is installed. It is behind the center mast in the sliding joint. A mx7 is way too heavy to have its entire weight supported by a 5/8”/16mm bolt. The cutter was new last october and has cut maybe 30 acres of pretty smooth...

Tractor is new, all pins in 7 pin connector do what they are supposed to do except the center pin. It should be hot. I have tried lights on and off, key on and off, engine on and off. Still no power. All fuses are intact, in place and plug is wired properly. I need power to run sprayer. The...

I got my new savage b-mag today. I was very dissapointed in the quality of the rifle. Cheap feeling and looking. Lots of plastic. It shot good on the otherhand although 2 of 25 cartriges misfired. Typical of winchester rimfire ammo. Save your money and wait for a ruger or remington version to...

A year ago i bought a new komatsu dozer that burned engine oil from day one. 3 months ago komatsu put a complete new engine in because of the oil consumption. Said it was a manufacturing defect. Anyway, the new engine is burning oil also so i had the dealer bring some oil out when he came to...

I have a couple of machines that are running a little warmer than they have in the past summers. I have always used cascade to flush out my radiators in the past. But my question to you all is, is there something better out there? What has given you all the best results?

Whats an upper and lower limit value for a JD MT? Its original paint so it certianly shows its age but it has been shedded since new. One owner, well one family the son has it now. Tricycle frnt. 3PH. Runs great. Dry rotted tires but they hold air. I have not examined it closely because of lack...

Does anybody here know how many gallons a 20.8x38 R1 will hold with the valve stem at 12 oclock postion?

Does anyone here know what a yard of size 57 crushed limestone weighs?

I need to make a few vertical welds with some sort of hard surface or wear resistant rods. I want to be able to either stack up the welds or make a big fat bead. I only have an AC welder and vertical is the only position possible. Any suggestions on rods, amps, technique, etc will be greatly...

I saw it mentioned here awhile back but cant find it again. Does anyone here know where I can order a rear tractor tire liner? I have a 20.8x38 tire that has a split in the side. The split is too long for a regular boot. I need a complete tire liner.

I just got a new komatsu D31 for my hired hand to run. Im gonna try to attach pics.

I have a freind with a D31 komatsu with both steering clutches stuck. He has tried to break em free under engine power with no luck. I am going to go see about it soon. Does anybody have any suggestions before I start on it?

My 135 gas with perkins engine is leaking gas from the carb where the electric fuel shut off screws in. The threads in the aluminun bowl are pretty much gone preventing me from being able to tighten it enough to stop the slow drip. Teflon tape has helped some but not enough. Any suggestions...

At what age did you let your kid start driving tractors on their own? How old were you when your dad "turned you loose" on a tractor? Growing up on a farm, my dad had me raking hay at the very early age of 8. I was doing simpler task before that. I am raising 2 sons now on the same farm. The...

I need to do an inframe overhaul on a JD 310A backhoe. It has the same engine as a JD 2550. I will probaly get my kit from shoup parts. I have been pleased with the kits I have gotten from them before but was wondering if there might be a better source. My question is do any of you guys have...

Can someone please explain this to me please. Whats the meaning and reason for these terms I keep seeing here? Such as, thumbsup, rolleyes, licking, drool, and im sure there are some others that I missed....

Why did I start getting email notifications when a new post is added to a susctibed thread 2 days ago? I did not change any settings and I find it very annoying. How do I stop em?