Right, I've fixed a double spool valve I had surplus behind the seat of my 1820, read up all about the need to insert a plug in the Yanmar hydraulic distributor & the need for a power-beyond sleeve in the spool valve, so I'm all set to plumb her up.
What size hydraulic pipes do others use? My...
Yanmar YM 1820 - does not start via ignition key. Previous owner had disabled connection to the starter solenoid & added jumper wires from solenoid battery & start terminals, now I think I know why.
He had also, wisely in my opinion, added a 25 amp blade fuse link in the white/red ignition...
I've just picked up a really nice little YM1820(see below) with the usual tractor wiring issues - I suspect connections behind the fusebox would be the main culprit. Ignition switch partly works but previous owner had bodged two wires to be joined under the the bonnet (hood!) to start her up. As...
I have an UTB 445DT which is the 4WD version of the Long 445. This is a selectable 4 WD or front wheel assist arrangement.
On mine the front axle can move forward or backward by over 1/8"!
I could, for now, slide in a brass thrust washer to take up this slack, but its clear the trunnion bearings...
I have a Long 445DT which comes fitted with a factory remote hydraulic valve intended to operate a double acting cylinder via two quick connects at the rear. Down feeds one connect & up feeds the other. It has previously been modified so that the lever-down valve outlet is piped to a spool...
I'm using a tractor with a TPH mounted implement basically for the first time ( an Universal 445DT sold as a Long445 or Allis 5045 in USA ) & running a 5 ft Rhino topper similar to a Bush Hog with a rear castor wheel.
I've selected position control & set the TPH arms for a suitable height to...
I'm having trouble fitting a toplink pin (3/4") to a Universal 445 (Long 445 or Allis Chalmers 5040 in US).
I've turned some pins to 3/4" on the lathe - they fit the toplink well, but I cant get them into the toplink housing on the tractor - there's no way to get a straight push on the pin to...
Just thought I'd turn up some 3/4" pins on the lathe to fit a top link to my Long 445 ready to run a bush hog & mower I'm picking up Wednesday night.
Pins are great & fit the top link easy, but cannot get them into the toplink support on the tractor.
There are 4 holes for the toplink pin, but I...
Just thought I'd turn up some 3/4" pins on the lathe to fit a top link to my Long 445 ready to run a bush hog & mower I'm picking up Wednesday night.
Pins are great & fit the top link easy, but cannot get them into the toplink support on the tractor.
There are 4 holes for the toplink pin, but I...
I have a backhoe with a subframe mount that doesn't suit the tractor I've bought - Long (Universal) 445 DT.
I was going to mount it on the TPH, but my tractor has a good quick release FEloader on it (See picture attached) & the brackets & rails for this are really meaty, like 3"X3/8" angle plus...
Should the TPH arms power down as well as up on the Long 445? Mine lift fine, but won't come down without some weight on them. This is my first real tractor so I don't know if this is normal. If it ain't, where should I look to clean/adjust/repair?
I just bought a UTB ( Long) 445 DT (4 WD) which has a FEL with spool controls in the cab, plus a single rear hydraulic Q/D outlet. I want to run a backhoer on this, which has two hydraulic pipes marked in & out. Assuming the "in" pipe is connected to the rear outlet, where should I connect the...
I just bought a UTB ( Long) 445 DT (4 WD) which has a FEL with spool controls in the cab, plus a single rear hydraulic Q/D outlet. I want to run a back actor on this which has two hydraulic pipes marked in & out. Assuming the "in" pipe is connected to the rear outlet, where should I connect the...
I just bought a UTB ( Long) 445 DT (4 WD) which has a FEL with spool controls in the cab, plus a single rear hydraulic Q/D outlet. I want to run a back actor on this which has two hydraulic pipes marked in & out. Assuming the "in" pipe is connected to the rear outlet, where should I connect the...