Search results

I have to clean everything (spreader/tractor) after spreading lime, and or fertilizer. Or else corrosion starts. Better to clean, than fight corrosion.

I have the Echo 590 Timber wolf. Great saw.

Another happy Echo CS 590 Timberwolf owner/user. I love this saw.

I ended up putting in ten quarts. I’ll run a while and recheck. Thanks for your help

Thanks Willy. I put 8 quarts in with a new filter, and it’s not even half way between the low and high. That’s why I’m confused. I don’t want to over or under fill it. When I drained it, I measured as best I could what came out at almost 9 quarts. Before draining, I check the oil level and...

I have a 2006 Farmtrac 550DTC tractor, it’s the Korean made by LS model, not the Farmtrac that looks like a Ford. It’s has a 4 cylinder Mitsubishi Diesel. I hope I can attach the photos from the top of the engine. Here’s where I need help, I can’t locate my manuals for it. I don’t recall the...

thank you!

Thank you very much!!

Hi Anyone know of an online Kioti parts dealer? Dealer I bought my Kioti stocks few parts. Other than Kioti oil and fuel filters he has to order parts for me. Besides the time delay, I get charged the shipping and handling to his dealership location, then add on several hours of my time to...

OP, any updates for us? Thank you

Inquiring minds want to know!

They are 1 7/16” nuts, the axles are 1” square. Since I felt the axles should spin freely like a roulette wheel, I was concerned I might have over tightened the nuts. I’m glad to hear that being very tight is the correct way. The axles spin, but only as I turn them. I imagine as others...

Thanks Ken. I was concerned about over tightening, thinking I could somehow stress, or impede the bearings. The axles each have a nut, and then a nylock(sp?) nut. I bought new Nylocks. After I use it a bit, I’ll check tightness, and snug the new ones on it. Thanks for your help

Thank you very much! I appreciate your advice.

Thank you very much. All 4 gangs spins, the rear two spin easier(freer) than the front two spin, but none are like spinning a something lubed. No noise, or bad bearing sounds. In other words I can turn them by hand, but not give them a spin, and they keep turning a while. I’m assuming that’s...

I have both. Anything in the future will be 4wd

Hi. I recently bought a used CountyLine (Tractor Supply) 7 foot Three point hitch disc. Three of of the disc plates were broken, so I removed the axle nut and jam nut off of two axles, and replaced them. I used my Rigid 18 volt impact gun, to tighten the 1 7/16” nuts on. I don’t have...

I’ve had an Echo Timber Wolf 59cc, 20 inch bar For years. Came with 5 year homeowner full Warranty. Use it a lot, plenty of power, always starts. Quality saw.

Please keep us updated with this. Interesting thread, sorry you have to deal with this, I hope TYM sorts it out for you.

Regen works, but I have to adapt to it in my M6060. I grew up running old iron, and never needed to run the high RPM to accomplish the tasks. The newer equipment needs to run at higher RPM, to get the HP and the DPF clean as others have mentioned. Years of conditioning of not having the RPMs...

Thanks. Finally got it off. But could not get the filter out of the housing. Manual doesn't show the separate parts of this cleanable filter and housin. Went to John Deere dealer and had to buy the entire assembly, plus separately the o rings. $100 dollars later, after another $300 in fluid...

I have the same problem On my 3203. Can’t get it apart. Manual is vague.

Old thread…. Did you figure it out? I’m stuck. Mine is one a 3203.

Hi anyone know how to get the CVT metal cover off of a Bush Hog TH440, after removing the bolts. no clearance between frame and the cover. I'm trying to locate a shop or service manual, no luck. Bet there is a trick to doing it. I have a rattle inside the cover and I want to take it off, to see...