Recent content by XCAT

my parts arrived last week to replace the cracked bevel gear on the side i have not done yet. photo above you can see quite a few teeth had cracks in them. photo also attached of the knuckle bush showing the wear. i couldn't understand why the bevel gear failed - until i stripped the full...

15 years old 975 hours, i like to turn over my gear when i can. i also wanted to make sure that happened before they put DPF on them over here. i just did major service and found small piece of bevel gear in the oil - see my post in operating section. i am rebuilding the front end as it is...

ok here are my old tractor on right EX50 Daedong and new Kioti EX5310 on the left. have spent the few days swapping bits between them and set the new one up. i have noticed the front end is MUCH heavier build than the old girl, i cant get the track the same on the rear because the axle housings...

hi Joe im a bit late to this party, but i think the DK only comes in Hydrostatic trans (higher cost i would think) and the EX only comes with Manual, i have a EX50 with 975 hours on it - had a few issues over the 15 years, i have just upgraded to the EX5310. i dont want hydro in my steep...

all, been ages since I was last on TBN. Our Daedong (Kioti) EX50 is now 15 years old has now got 975 hours on it and was due for major service. All went well until I drained the right hand bevel gear oil, I always drain it by removing the lower rubber bearing cap – after removing the cir clip...

the tractor is the same as a DK50 i think in the states. and yes always have at least 900LB 3pl load on the tractor

hi all, i havent been on for a long time, now have 975 hours on mine with heaps of heavy front end loader work. just doing a service on our EX50 and found a piece of tooth in the drained oil from rh front bevel hub. - i always remove the lower cir clip and plug to drain the oil rather than the...

hi, i had a similar issue a while back with lost drive to the front, check my thread here EX50 No 4WD suspect hydraulic pump not sure if thats the correct way to list it but may be the same issue.. cheers

so i machined a deeper groove into the solenoid valve to keep the cir clip in place on both the pto and 4wd valves. spent around two hours carefully cleaning up the damaged spools, and hand lapping and all went back together well, put it back on tractor and everything work again and steering is...

ok some news, i tested with pressure gauge today and no pressure at all from the 4wd port - two days ago i had some flow but none today, tractor still has some steering so i dont think the hyd pump is at fault. so i removed the modulating valve and stripped it down slowly and bagged each valve...

Hi all, we have a Daedong EX50 @ 700 hrs - i think you would know it as a DK45 / 50. very well serviced. working to day and noticed that it lost 4WD, no noises heard - so off to the workshop to check it out, have checked all electrics and found fuses ok, power and earth at the 4wd solenoid on...

here you go, arrow points to the drain hole, in this case the cir clip is in correct location and oil will drain, but if cir clip rotates the hole will be blocked and oil can not be drained. I hope this helps. cheers

hi all, i am looking at getting a gravely pro turn 252 XDZ, ( zero turn ) i notice that there is no mention of this model on this site, can anyone tell me if that model is used in the states ? , i tesed one today for 1 hour and am happy with the cut finish, only slipped sidways off embankment...

hi everyone , has anyone had any luck cross referencing daedong (Kioti)hydraulic oil filter part number T4620 38032 . i would like to be able to get these from Donaldson if possible. :licking: thanks Aaron