The next step for me was to re install the sub frame for the backhoe. If you don't have the backhoe you will omit this steps of course. I used a jack to make sure the bracket holes would line up. I put in the very front bolt, than swung it up into place and added the rear bolts. Once all bolts...
Next step is to re attach the rear back brace that ties in the two ROPS main frame braces. You will need a punch awl to line up the holes as the system is really tight. Be careful not to strip threads. You can also re attach the gas tank strap.
The next thing you will want to attach is the...
Got to finish up the tractor today and I have to say "WHAT A RELIEF" its ALL done!!!!
Here are the steps I took to put the tractor back together. Take it slow because putting her back together smoothly means re installing stuff a certain way.
I started off with the seat. Make sure to re...
Step 10. Now its time to install the levers. I started with the bolts which have jam nuts, make sure you put those on first. Once they are on I started with the inside lever which is closes to the seat. You will need a 17mm wrench for this and after you install the lever you can now tighten...
Step 8. Now its time to install the quick disconnects for the rear remotes. I have a couple of different types of sealant but I am going to use Loctite 545 for this job.
Step 9. THIS STEP IS ONLY IF YOU HAVE THE BACKHOE....
Now I went to 2 different hydraulic parts stores here in town and...
step 6. Once all the banjo fittings have been tightened down, you can now tighten the three bolts that hold the manifold onto the base plate.
Step 7. The rear remote manifold and pipe fittings with the front and back plate that looks like the symbol of the black widow. The instructions give...
step 5. Install overflow tube. But first you need to add o-ring grease to the tube and oring provided. Than take off the plug on the transmission. Once completed install tube as shown.
step 4. Install new dual remote manifold with the included 3 bolts. Do not tighten them right now. Once that is installed you can now install the new main supply line from the bottom of the FEL block to the dual rear remote valve body on the top left. ALL BANJO FITTINGS will have two copper...
Step 3. SKIP THIS STEP if you don't have the backhoe installed....
The factory installs two hoses for your backhoe. One hose is hooked up through your joystick on top.
The second hose is hooked up on the FEL block down below.
This leads me to my grief with this kit. The kit does not give...
step 2. This part is for anybody who has the FEL installed on your tractor. The FEL block is underneath the step platform outside of the forward and rear peddles. The block will have a banjo hard plumbed pipe going from the FEL block to the top of the transmission. This pipe has to come off and...
After receiving the wrong kit which is literally for all the rest of the small compact series tractors, this kit is ONLY for the XG3025 tractor to include the hydrostat and 12 speed shuttle shift.
DISCLAIMER, Some steps in my install were not shown in the install manual and I figured them out...
14.) Another critical part. The brake pedal needs to be pushed all the way down and held down with the piece of wood again. This will also cause the brake clutches hanging on by a thread in there slots. You need to be very careful or you will knock the clutches out and into your gasket maker and...
10.) Now the nut has been torqued down, its time to use a punch die to bend the tb in on the shaft indention. You want to use a punch just the size of the shaft indent. Do not over do this as you can break it off. Just enough that it will not allow the nut to back off.
11.) Now its time to cry...
8.) Time to install the shaft into the final drive casing. This task could be done easier with two people but once again I had to do it by myself. In my case I had the final drive on my jack platform with the 4X4 wood block under the final drive casing to keep it level. Then you have to...