Recent content by Trap

thx, space is tight in there.

Has anyone removed the hood on one of these? I have a leak (head gasket?) and need to look around. any help is appreciated. thx

After seeing a small leak inside of frame I eliminated usual spots ( thermostat, cap, radiator.) must be the water pump. I can't really see a leak but it must be something to do with the pump. it is hidden behind the lower hose. So I have new Kubota hoses and water pump. Now the next nice day I...

I must have some debris in my fuel tank. flow to filter was a trickle and tractor wouldn't run more than idle. I blew air from filter back to tank and flow rate was 100 time better. this tells me something is going on in the tank. So if any one has any good tips for removing the tank or other...

I recently bought a Tractor Supply Mid buster and a subsoiler to break up my garden a bit.I have a Kubota B7610 24HP. I need help or photos of what correct adjustments look like. Although I haven't spent but 30 min. playing with this my first pull on the sub soiler only went 8-9 inches deep. I...

OK, I need opinions on which might be a better fit. I am looking at a Leinbach model 19-12" or a Frontier one bottom 14" plow. This will hook to a Kubota B7610 4WD. The Leinbach is a little smaller and priced around $500, The Frontier is heavier duty and sell for $560. The Leinbach dealer thinks...

I know this has been beaten to death but I haven't seen this question yet. TSC has both the subsoiler #2128333 and the midbuster #2128228 priced at $120.00 locally. This is somewhat less than their web price. Queston is would it be better to get the subsoiler and add a furrower or get a...

I have a Kubota B7610 25HP tractor 4WD. Looking for a plow for garden plots. Looked at Leinbach model 19-12 made for smaller tractors, also saw the model 81 which looks larger and stronger. I also saw a JD 14" but my control arms would have to open to 27" whereas my other 3pt stuff has the pins...

I just did my 50 hr service yesterday and only got 2.5 gal. out of the three plugs & two filters (haven't pulled strainer yet, I need a socket). The book says capacity is 4 gal. Am I missing something? Any help will be appreciated.

I have a rattle on the deflector chute on my Kubota MMM. There is a bolt on the deflector that rests against the mower deck and rattles like heck on anything other than very smooth surface. I really see no use for this bolt. Are there any owners out there with the same bolt, and is there...

Has anyone ever tried locking up a 60" Kubota mmm to do some loader work? the book says to raise the deck (impossible to get that high) and pin the front of the deck with supplied pins into brackets. It is almost impossible to lift a 300 lb deck & place pins. It also looks to be very close to...

I think I am in need of a new piece of equipment (just a buying urge) and the subsoiler looks like it might work to break up ground for planting of new flower beds and such. I really don't know what all they might be used for. If anyone has projects to share let me know. Also someone stated on...

I have seen a few posts on this subject along with many discussions on the topic of where to attach chains on a tractor for trailer hauling. I know about chain, binders, trailers, etc., but I still need a few ideas or better yet, pictures of different ways you good folks have attached binding...

I know I opening up a can of worms here. But, I have never heard what the real problem is with using the Chinese made chain. Looking at a grade 70, 3/8", for booming down a 24 HP tractor. Can it be that bad? Don't hit me too hard , just asking.

I knew Markhams Welding was unable to get teeth for their toothbars when I ordered a Markham toothbar over three weeks ago. but am curious whether anyone has received theirs in the past week or so. As far as I know I am on hold until.........? Thanks, waiting in KS