Menu
Forums
Today's Posts
New posts
Search
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Marketplace
Register
Log in
Join
What's new
Search
Search
Search titles only
Today's Posts
New Posts
Search
Members
Current visitors
Top posters of the month
Menu
Log in
Join
Database
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
RandyT's latest activity
R
RandyT
replied to the thread
Honda FRC800 Tiller, Aftermarket Belt?
.
That belt is that price because it is somewhat of a specialty dimension. Standard B belts are 21/32 by 7/16 or .65625 x .4375 A 5L...
Mar 22, 2024
R
RandyT
replied to the thread
L3010 PTO won’t disengage
.
Cable frayed inside of covering could also be possible.
Mar 20, 2024
R
RandyT
replied to the thread
L3010 PTO won’t disengage
.
I don't know if I have the correct diagram but take a look at item 20 on this diagram to possibly give some direction...
Mar 20, 2024
R
RandyT
replied to the thread
Loader
dk55 and KL551 counterweight
.
My DK45S/DK451 with the Bushhog M346 loader calls for 2300# of rear counterweight
Mar 20, 2024
R
RandyT
replied to the thread
Mini-Skid Steers - Are they good or bad?
.
All can be tipped if not careful. Most machines up to 1000 pound ROC are 36-42 inches wide. Above that they are closer to 46-48 wide...
Mar 19, 2024
R
RandyT
replied to the thread
Mini-Skid Steers - Are they good or bad?
.
Nephew runs a Ditch Witch SK600 with his stump business to clean up wood chips. It has its limitations but really speeds up progress on...
Mar 19, 2024
R
RandyT
replied to the thread
Gas Proof Plastic Repair Sealant?
.
For the white plastic fuel tanks used on some mowers. A hot glue gun will seal the hole and is not effected by gas.
Mar 18, 2024
R
RandyT
replied to the thread
Kawasaki FH680V-A26 Carb
.
Most likely the Nikki carb is OEM and should take float number 16031-7001 But that looks like you should have the 15004-7029 carb not...
Mar 17, 2024
R
RandyT
replied to the thread
6x4 (I think it's called) side by side
.
There is no clutch just a centrifugal belt drive system. Sounds like idle speed is too high preventing the drive belt from fully...
Mar 17, 2024
R
RandyT
replied to the thread
Need help picking correct oil for my 25 year old 19hp twin Generac generator
.
Wording over the years has changed. Current small engines recommend the first oil change after 5 hours on engines without oil filter...
Mar 16, 2024
R
RandyT
replied to the thread
Need help picking correct oil for my 25 year old 19hp twin Generac generator
.
Breakin oil is an oil that doesn't have friction modifiers to assist in the seating of rings to the cylinder for better compression...
Mar 16, 2024
R
RandyT
replied to the thread
Need help picking correct oil for my 25 year old 19hp twin Generac generator
.
I just service and warranty the portable products and for the most part don't service the standby units, other than when my regular...
Mar 16, 2024
R
RandyT
replied to the thread
Need help picking correct oil for my 25 year old 19hp twin Generac generator
.
Went and looked at a couple service manuals. And it says that the generator is run and tested at the factory, and no breakin required...
Mar 16, 2024
R
RandyT
replied to the thread
Need help picking correct oil for my 25 year old 19hp twin Generac generator
.
Been working on, rebuilding, and replacing small engines on lawnmowers etc for over 26 years, and I have never come across an OEM that...
Mar 15, 2024
R
RandyT
replied to the thread
Need help picking correct oil for my 25 year old 19hp twin Generac generator
.
All of the modern small engine oils contain ZDDP So Briggs, Kohler, Honda, Stens, Kawasaki, Kinetix, other brands small engine oils...
Mar 15, 2024
Database
Top