Menu
Forums
Today's Posts
New posts
Search
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Classifieds
Auctions
Database
Quick Review
Quick Owner-Page
Register
Log in
Join
What's new
Search
Search
Search titles only
Today's Posts
New Posts
Search
Members
Current visitors
Top posters of the month
Menu
Log in
Join
Forums
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
number two's latest activity
N
number two
reacted to
Henro's post
in the thread
backhoe question.
with
Good Post
.
This is a good point. Putting a 3PH backhoe back on the tractor can be difficult sometime. Maybe most of the time? That is another...
Jul 8, 2025
N
number two
reacted to
anomad's post
in the thread
oil and hydraulic mixed accidently
with
Good Post
.
What does the normal service interval call for? My Kioti calls for a hydraulic oil change at 400 hours. So you are right there. The...
Jul 7, 2025
N
number two
reacted to
Harry in Ky's post
in the thread
oil and hydraulic mixed accidently
with
Good Post
.
I wouldn't worry much about it. Personally, I get tired of all the comments I see involving "change the fluid and filter(s)" every time...
Jul 7, 2025
N
number two
reacted to
oldnslo's post
in the thread
oil and hydraulic mixed accidently
with
Good Post
.
How much oil does the tranny hold on that tractor? If 10 gallons like mentioned I would be far less concerned than if it only held 3 or...
Jul 7, 2025
N
number two
reacted to
RjCorazza's post
in the thread
oil and hydraulic mixed accidently
with
Good Post
.
I use the same 1 gallon oil filling can between hydro and engine oil without cleaning it out between, but that's about as far as I go...
Jul 7, 2025
N
number two
reacted to
sunandsand's post
in the thread
Looking for 24mm or 15/16" pins
with
Good Post
.
GRS, I mostly agree with you. I also modify all kinds of things, and usually (hopefully) improve them for my uses. I'm absolutely not...
Jul 7, 2025
N
number two
reacted to
sunandsand's post
in the thread
Looking for 24mm or 15/16" pins
with
Good Post
.
I agree, the ever-so-slightly enlarged hole would probably not be noticed. If however the failure of the ROPS was involved, you can...
Jul 7, 2025
N
number two
reacted to
sunandsand's post
in the thread
Looking for 24mm or 15/16" pins
with
Good Post
.
Strongly suggest finding and installing the correct factory part and keep the receipt. The ROPS is a (now required) safety item. As we...
Jul 7, 2025
N
number two
reacted to
Joe Batt's post
in the thread
Looking for 24mm or 15/16" pins
with
Good Post
.
With the additional benefit that you will then immediately find the one that you lost.
Jul 7, 2025
N
number two
reacted to
sixdogs's post
in the thread
Looking for 24mm or 15/16" pins
with
Good Post
.
In had the same issue and weighed my time and effort for something that may not work and bought the pins from the dealer.
Jul 7, 2025
N
number two
reacted to
fruitcakesa's post
in the thread
Generator shot down procedure
with
Good Post
.
After living without a generator for 35+ years, I finally broke down and bought a Champion 5500 inverter genset since it seems we have...
Jul 7, 2025
N
number two
reacted to
grsthegreat's post
in the thread
Attaching pto implements
with
Good Post
.
Recheck post #19, use an overrunning clutch. Cheap device that will solve all your issues. They carry them on amazon, tractor supply, etc.
Jul 7, 2025
N
number two
reacted to
ptsg's post
in the thread
Attaching pto implements
with
Good Post
.
Your tractor uses a wet clutch for the PTO with a spring loaded brake. Once the PTO is off, the spring loaded brake kicks in and keeps...
Jul 7, 2025
N
number two
reacted to
Complete Turf Care's post
in the thread
Pictures from an athletic field contractor
with
Good Post
.
Today we did some verticutting on golf course greens. We ran the machines in two directions. This is what it looks like after it's...
Jul 7, 2025
N
number two
reacted to
WinterDeere's post
in the thread
4 WD operationI
with
Good Post
.
I guess with today's modern self-priming diesels, it's not as big a deal. But on the old ones (my 750 and 855), just remembering the...
Jul 7, 2025
Forums
Top