Recent content by LetsRoll

The motor is a dayton 1/4hp that I got from Tractor Supply (TSC).

My current setup (Dillon RL550B).

Just a few pictures to tease the OP. My video wet stainless steel tumbling. http://www.youtube.com/watch?v=e5K84hNa7bE

Gents, what is the difference between the two calibers power wise? Or should I ask, does the .45 have more take down power than the .40? Reason I'm asking is cause a few days ago, my family had a break in and the thief stole my Sig Sauer P250 9mm pistol. So before I purchase a new Sig Sauer...

I couldn't find a way to change my blades and clean the deck of my mower safely. So I decided to put it on my vehicle lift. Of course, I strapped it down to the lift. You can see the straps in some of the pictures. Pretty soon, I plan on building an adjustable drive on platform. Just need to put...

I'm in the process of building a waste oil burning stove for my shop. I got the idea from a web page I was reading at mother earth news Roger Sanders' Waste Oil Heater. Then some folks took the stove to the next level. So, I decided I was tired of wasting money on buying LP for the radiant...

Just finished redoing my landscaping/rock rack. So, I decided to weld up a toothbar. I got the shanks, teeth and pins off of ebay for $175. I already had the steel. The plate steel is 3/8 inch and the side brackets that are welded on are 3/8" as well. Since I already had the steel, total bill is...

I stole a set of Pats Easy Change on ebay for $99.99 (total bill after shipping was $119.99). I was going to make a quick hitch, but decided against it cause of the cost for machine work. Pats website states you need 4 inches to be able to use these on the 3 point. I measured mine and I'm 1/2...

I've been wanting to add mirrors to the sides of my canopy so that I could see the outside of the tires. I've been doing allot of driveway grading here lately thinking I could do a better job only if I had a set of mirrors attched to the side of the canopy. While I was thinking about how I...

I was doing some landscaping today and the pin that holds the rake together broke in half. This pin makes the rake useless to use as you can see in the pictures. Just wondering if this was your rake, would you try to repair it or take it back to the dealership where I bought it (same place where...

I just went to a auction on Saturady and really enjoyed myself. Me and my Father-n-Law hooked up the trailor to my truck and off we went. We talked the whole way there. After reading the listing in the local paper. I knew what I wanted before I even went to the auction. I ended up coming home...

I finally got around to building a road grader. It turned out better than I expected. Also, performes rather well too. I've already plowed up the field in front of my house. So, I needed an implement to smooth it out in a timely manor. I tried using a rock rake, but I wasn't happy with the...

My new two bottom plow (or I should say my old). I purchased it to plow up some rough land that needs allot of attention. Last summer since my area didn't get allot or enough rain. I had to feed the horses hay almost all of the summer months. Well, in the pictures some of the grass has came...

This is a boom pole with a basket on the end of it. I welded it together to help trim the tree lines. Its attached to the FEL by means of the FEL pallet forks. The forks are rated at 3500 pounds, so I don't have to worry about them bending or snapping off. I'm not completely done with the basket...

I did some bush hogging a few weeks back and after getting burnt up, I decided to make a canopy. Buying a canopy was out of the question since I had limited door clearence in my shop (8ft doors). This canopy is made out of 14 ga sheet metal and 1in. square tubing. The side supports are made out...