Recent content by LeadPoison

Anyone know of an online source for Bush Hog parts? I had pin rust and refuse to take grease. The zerk is fine and I have hammered the pin back and forth with WD40 and broke it loose, but it still won't take grease. It the pivot pin that connects the arm to the frame arm just in front of the...

I have been preparing the food plots with a 6.5' disc harrow that weighs about 900# for many years now. We do about 20 acres or so a year. Ground is in South Mississippi. The tractor is 2WD and the fields are flat. What width lift disc could I get away with? I don't need anything offset...

Found these for sale in my area. What make are they? Worth a buy? They are CHEAP.

We contracted someome to do some dozer work on our land a while back. Two relatives and myself walked the property with the guy and showed him what we wanted done. We asked for an estimate of time as we had a budget. I got a bill for 2.5X the verbal estimate. I was never made aware it was taking...

I have a 2 row planter and will be panting 5 acres of corn shortly. The bags say the corn seed size is F17 and was wondering what plates matched up to that. I can't seem to figure it out. Thanks.

I plant about 18-20 acres of food plots every fall and I want to do about 10-12 acres in the spring. My property is located in southwest Mississippi in the delta area. No rocks. Near the the river. Very fertile. We have a Kubota M4900 with a six foot Tufline disk and a 6 foot cutter and...

It's time for the 50 hour service in my M4900 2WD gear drive. I went to NAPA today and bought 2 gallons of Shell Rotella 10W-30. Hopefully no problems there. NAPA had one tranny/hydro fluid that was Kubota UDT rated BUT only in $10/gallon containers. They did have another one which was rated...

It's time for the 50 hour service in my M4900 2WD gear drive. I went to NAPA today and bought 2 gallons of Shell Rotella 10W-30. Hopefully no problems there. NAPA had one tranny/hydro fluid that was Kubota UDT rated BUT only in $10/gallon containers. They did have another one which was rated...

I am heading up to the deer camp this weekend to do some tractor maintenace. My manual is up there and I need to know what the capacities and specs for the hydraulics/transmission and engine oil are. I already have the the hydraulic and oil filters and will be stopping by NAPA on the way out to...

I am probably going to pull the trigger on a new Chevy 2500 this week. I only pull 10K (tractor and trailer) 600-700 miles a year so the cost of the Duramax/Allison really isn't justified nor affordable for me. I don't need 4WD. My question is which axle ratio should I go with and what type of...

which one and why? I like the Yetter #71 the best, but it isn't available in my area. Covington is.

I am thinking pipe and concrete as the main guts of it. I thought about getting some 2" pipe and welding some rebar around it to it to make a internal frame. I would then insert that into a much larger pipe. Fill with concrete. Then take some heavy rod and insert it into each 2" pipe end. Then...

And didn't even know! I am a bad bad man. So I was looking over the LA Dept. of Motor Vehichles website last night and it turns out I need a Class A CDL to pull my tractor and trailer. Whoops. Any trailer that is rated to carry over 10,001 pounds must be pulled with a driver with CDL. I can...

My Kubota M4900 spec sheet says it has a Cat I and II hitch. I have spacers that I put on my harrow pins so they fit the lift arms. On my Woods 720 medium duty cutter the lower pins fit without the spacers on the hitch, which makes me think it's a Cat II implement. Question: Does a Cat I and II...

Anyone know the engine foot pounds on the 54 HP version of the M4900?