Menu
Forums
Today's Posts
New posts
Search
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Marketplace
Register
Log in
Join
What's new
Search
Search
Search titles only
Today's Posts
New Posts
Search
Members
Current visitors
Top posters of the month
Menu
Log in
Join
Forums
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
laurencen's latest activity
laurencen
replied to the thread
Homebuilt grader
.
many years ago picked up a Bobcat grader, its lighter than the current models, after using it sor 10 plus years I still yet to gea a...
Mar 11, 2024
laurencen
reacted to
Seven Gables's post
in the thread
Need to adjust the thumb pressure on my Bobcat mini excavator
with
Good Post
.
yes end without shaft. Just want to make sure you’re adjusting the port relief that regulates the base end of thumb cylinder. My jam...
Mar 11, 2024
laurencen
replied to the thread
ToolCat Step Kit
.
that sure looks like it was made for the machine, will order up a couple next week
Mar 10, 2024
laurencen
reacted to
johns_dmax's post
in the thread
ToolCat Step Kit
with
Good Post
.
Sure, not much to show though. I set it as far down and forward as it would go and it just fit. I didn't use any of the mounting...
Mar 10, 2024
laurencen
reacted to
turbo36's post
in the thread
New E60 Excavator
with
Good Post
.
After four surgeries in the past three years, I can’t lift or run a shovel anymore. Decided to get a little help!
Mar 9, 2024
laurencen
replied to the thread
ToolCat Step Kit
.
they look neat could you put a couple pictures of the underside mounting, thanks
Mar 8, 2024
laurencen
reacted to
2manyrocks's post
in the thread
3pt post hole digger vs one man auger vs Groundhog Digger
with
Good Post
.
One of my friends not far from here couldn't even set T posts without first drilling a hole with a rock drill.
Feb 17, 2024
laurencen
reacted to
ruffdog's post
in the thread
If you have Toolcat questions, ask them here...
with
Good Post
.
The service manual isn't the best I have worked with and it sure isn't the worst one either. For me, I would agree and say it is worth...
Feb 13, 2024
laurencen
replied to the thread
New Toolcat Purchase
.
wish we had snow like that, couple weeks ago we had 4 inches, fun in the toolcat but not worth clearing it, did anyway
Feb 13, 2024
laurencen
reacted to
AdmiralS's post
in the thread
New Toolcat Purchase
with
Good Post
.
Another few hours of snow to go and then get to go out and play! They reduced the forecast but we have already gotten more than they...
Feb 13, 2024
laurencen
replied to the thread
If you have Toolcat questions, ask them here...
.
i would say yes,
Feb 12, 2024
laurencen
reacted to
AdmiralS's post
in the thread
New Toolcat Purchase
with
Good Post
.
Today was the day! The conclusion of the 14 Month Journey! And perfect timing with the 15+ inches of snow we are expected to get...
Feb 12, 2024
laurencen
replied to the thread
Bucket link Hack...
.
if you indeed want the bucket to tilt more before I played with the linkage get a quick adaptor plate, weld it 90 degrees to the ground...
Feb 6, 2024
laurencen
replied to the thread
Bucket link Hack...
.
agree, looked at mine and it will tip the underside of bucket past 90 degrees to ground when full height, all I can think of either he...
Feb 6, 2024
laurencen
replied to the thread
Bucket link Hack...
.
Iv used bucket tilt to get out of snow many times and does go past 45 closer 90, what angle is on the bucket mount, that will change how...
Feb 5, 2024
Forums
Top