KangerooL48's latest activity
-
KKangerooL48 reacted to bmaverick's post in the thread Forum for air cooled diesel engines and clones with
Good Post.
Yes, with FreeCAD anyone can now open 3D and 3D files and easily share or work with them. When you launch FreeCAD, it begins in the... -
KKangerooL48 reacted to jcrotts110's post in the thread Forum for air cooled diesel engines and clones with Good Post.
I just joined up to make a few comments here. I have a 186fa installed in an Allis Chalmers Big Ten. I ordered the 406cc, but for some...
-
KKangerooL48 reacted to jcrotts110's post in the thread Forum for air cooled diesel engines and clones with Good Post.
Here are the photos. The old engine was beyond finished. You could move the crank all over the place. The bearings were worn out You...
-
KKangerooL48 reacted to ponytug's post in the thread Forum for air cooled diesel engines and clones with Good Post.
To close the loop on this issue: I traced this back to an air leak at the intake of the fuel pump, where the solenoid threads into the...
-
KKangerooL48 reacted to ponytug's post in the thread Forum for air cooled diesel engines and clones with Good Post.
Aaaah. I now understand what you did. Brilliant! All the best, Peter
-
KKangerooL48 replied to the thread Forum for air cooled diesel engines and clones.“I tend to use nylon pull ties (zip ties) to hold things in position; I make to many mistakes for glue.” I usually do the same. However...
-
KKangerooL48 reacted to ponytug's post in the thread Forum for air cooled diesel engines and clones with Good Post.
I tend to use nylon pull ties (zip ties) to hold things in position; I make too many mistakes for glue. I would have to go check on the...
-
KKangerooL48 reacted to gbrecke's post in the thread Forum for air cooled diesel engines and clones with Good Post.
I'd like to chime in here as a student of the Chinese Yanmar clone. No doubt the original has proven itself. My frustration with...
-
KKangerooL48 reacted to 90cummins's post in the thread Forum for air cooled diesel engines and clones with Good Post.
How many hours are on the engine?? It sounds like mine did when the cam bearing was failing. Check the oil filter/strainer for...
-
KKangerooL48 replied to the thread Forum for air cooled diesel engines and clones.Checked fuel pump rack engagement with forked lever was correct. Loosened throttle plate to properly check govenor springs position and...
-
-
KKangerooL48 reacted to ponytug's post in the thread Forum for air cooled diesel engines and clones with Good Post.
My bet is on a defective seal around the solenoid to injection pump. I suspect that there's just enough air to prevent building speed...
-
KKangerooL48 reacted to 90cummins's post in the thread Forum for air cooled diesel engines and clones with Good Post.
When I rebuilt my engine I recall that it also ran poorly with no load, smoke, skip, stumble ect. After I wired the generator so I could...
-
KKangerooL48 reacted to ponytug's post in the thread Forum for air cooled diesel engines and clones with Good Post.
Welcome to TBN! Is your fire pump a Darley, or some other brand? I'd love to see a photo. Yes, that's abnormal, and that seems like a...
-
KKangerooL48 reacted to arto98607's post in the thread Forum for air cooled diesel engines and clones with Good Post.
How long does the "starts and splutters away with blue/black exhaust" last after the startup?
-
KKangerooL48 replied to the thread Forum for air cooled diesel engines and clones.Thanks for your prompt responce. I have been editing my initial post to correct any errors and add some additional information I had...
