I was planning on a electric dual vbelt clutch from a zero turn.
I did have a 4ft mott tow behind flail with a 18hp on it and it work great but I kept on loosing blades
The next flail I'll have to weld on bigger mounts and put on hammers.
Well I see a 6ft flail mower has shown up on my local marketplace cheap,
Now I'm wondering how big of stand alone gas engine would you think would be required to run it well 18hp, 25hp, 30hp?
This wouldn't be PTO powered as its going on the front of my mini skid steer (toro TX1000)
I have a...
Well I let my property get very overgrown, so much that my gravely walk behind(and me) just can't keep up.
I tried trimming the front and back of the deck on a cheap lawn tractor but I had to stop every few minutes to get the chainsaw out for anything over 3/4"
Last summer I dug up a 40"...
As the title saids, I'm looking at goverment auction of what I think is a BCS 730 (8hp kohler magnum) with a large power brush.
I had a power brush for my gravely 5240 and it was great for clearing the sidewalks, but I sold it didnt think I'd need it then....
Now I'm needing to clean my road...
Well I saw a set of gear reduction wheels on the local craigslist, and was wondering do you guys think it they would fit on my 5240?
I did a engine swap a while back but all my power is up in the higher throttle so even in low low its a bit to much when I'm doing a bunch of snow.
Well I was at a auction today and picked up two Gray Model 100 air lift now I'm thinking they both work and can haul either end of my jeep up fast.
Now how do you guys think I can combine them to lift both ends or side simultaneously? Or other project for them.
Now I'm not dumb got some 3"...
Well I'm in the process of getting a new welder, I currently have a little Lincoln weldpack100 kind of wimpy and my big Lincoln weldandpower 225 but I dont want to take the time to hook up my LN-7 and then go deaf running the engine on the weldandpower all the time when I want to weld more than...
Well I got a LN-7GMA from work for free the other day :thumbsup: it needs some paint, a gun, and a feed roll but it works, save for the preflow, and purge/cold feed switch.
Now the only CV power supply I have is my weldanpower 225 it will do 20volt at 200 amps not bad! When my current mig is...
I'm just having a thought, I friend has a rotary plow gearbox(just the gearbox nothing else) that he might give me for free if I can find a cool use for it.
So I'm thinking well drilling rig, I take a 3 foot section of Hex stock bore it out to lets say the OD of 1" black pipe, and weld on a...
Well, it stopped snowing and its time to plow. I was given a bunch of attachments, and one was the rotary plow and the other was the rototiller attachment for the plow attachment.
Now I'm debating which to use the rotary plow, or the rototiller.
The garden in question is mid size I guess...
OK guy lets see if we can find me a winter project to do with this hydraulic motor its a Char-Lynn 101-1032-005 its 22.6cu its bolted up to a what I guess is a planetary gearbox
Surplus Center - 22.6 cu in CHAR-LYNN 101-1032 HYD MOTOR
I need to clear out my bench at work and its sitting there...
A friend seeing that I just bought a 5240 told me he had a old gravely in his back field I could have with some attachments. Well I got it home, and got the leaves off of it and dropped on a battery. Greased and beat the starting chain loose. Added some gas found the tank has a crack in the...
Well I have a gravely 5240 (8hp) with the 44" power brush I'm loving it for doing my sidewalk so much most times I do the whole blocks! :laughing:
But I only think the brush is good for 1"-3" and I know heavier snow is coming So soon I'm going to pick up a plow and some other attachments for...
Well I just got my $175 Gravely 5240 home it came with a 44 inch power brush.
Its in great condition, But with one small problem its PTO level needs to be tied in place or else it will slip out and grind.
Why is this? Bushing? need new fork?
Well a while back I bought a little harbor freight trailer I beat it hard so I rebuilt it. And I beat it harder. So I'm re-rebuilding it and making it a dump trailer to use with my jeep for hauling misc junk to the scrap yard (I get crazy stuff, had 900lbs of bolts last week)
So the pictures...