I started my search today looking for a starter for my Chinese Tractor that has a Benye Motor. I realize that Benye makes motors for a lot of named tractors but here is my question.
Does the starter I am looking for (#QD1315) exist under another part number for another brand of tractor. I...
I recently replaced the injectors on my tractor because there was to much leaking of fuel into the crankcase. The repair shop suggested I get the old injectors rebuilt in case I need one in the future.
I live up in north Idaho so services are rather limited. Can someone help direct me to a...
I am looking for a source to buy some retaining clips that holds that two parts of my tractors air filter together . I have attached a picture of it. Can anyone help me. Thanks Craig
Hi guys, I have an old but reliable Kobelco K905LC Excavator. I have a question about greasing the bearing unit of the lower unit. There are four zurk fittings that, according to the schmatics. grease a ball (resumably a ball bearing) It normally takes about four pumps from the grease gun to get...
Looking for some answers to a new problem.
I have a tractor sold under the name of Hercules - Model 3304. It has a Benye T13951T engine and is a reverse steer tractor and served me well this snow season while using a snow blower. I purchased it in 2004 and it has very few hours on it, perhaps...
Thanks to everyone's help in getting my air brakes retracted so I can move my 1976 International Loadstar Dump Truck. In addition to getting the brakes freed up I also removed the back portion of the drive line. I found that the two speed rear axle still is in some gear and not in neutral. Is...
As noted in previous emails I am attempting to relocate this truck from Washington State to Idaho. It does not run and inorder to get it there it will need to be hauled. The title does not show the weight of the vehicle so if someone could make a good educated guest it will help me with answer...
To make a long story long here is my dilema.
I have a 1976 International loadstar 1700. During a pretty good week of rain, and with the hood off the engine filled with water which has lead to a stuck engine(304 CI). I am working on trying to free up the engine now so if you have some ideas on...
I have a 905 Kobelco excavator that works pretty good and does not have a lot of hours on it. Lately when I have used it the left track sticks and will not allow me to turn very well. After awhile it breaks free and runs fine for awhile then back to sticking again.
Is this a problem with the...
A neighbor of mind is selling a brush hog/mower deck made by Modern Manufacturing. I have not heard of this company before and perhaps they make other similar attachments under other names.
Does anyone have any experience with their equipment. What is a fair value for a 60 inch cutter.
Thanks...
I am calling upon you all for your wealth of information.
Here is the situation. I have a Hercules tractor that has a Beyne engine. It is a reverse steer tractor that hosts a 60 inch snow thrower on the 3 point hitch. The complete package works great.
My problem is I have no way to steer the...
I recently registered with TractorbyNet and find this a very useful sight. I have also attempted to find what I am trying to learn from reading all of the throughtful comments of others. I am still confused with the operations of a hydraulic cylinder and valve so I come to the experts out there...
Can anyone tell me if there are after market parts for Komatsu Dozers (D37E) that are priced less then OEM. For example $3,500 for a new Crankshaft seems a little steep. Any information would be helpful.
Craig Buscajoia@comast.net <font color="blue"> </font>
I am considering the purchase of a Komatsu DP 3 model dozer. The cost of replacement parts for Komatsu seem a little scary compared to what I have paid in the past for my Case Backhoe.
Can anyone help me by letting me know of any aftermarket parts manufacturers for Komatsu Dozers or if not who...