Recent content by cmuncy

Good morning campers, It's been a while sicne I've been on but I need some assistance. On my 5140M FEL on my FarmTrac 300DTC, I need seal kits for all 4 cylinders and I really need 1 new cylinder (bent piston, don't ask how...) Here are the part numbers for what I need: 903341 Hydraulic...

2 years ago I had about 5 acres cleared in to 4 rather large piles. We attempted to burn one, and let's just say, with the winds coming and going, it was more than I want to procede with. WIth that being said, I got a few bids for contractors to come in and mulch the remaining dry burn piles...

Looking at a good deal on a 2" water pump at TSC: Tractor Supply Company - Pacer Pump 3.5 HP 2 in Plastic I know this is a great pump for moving water, but what about a pressurized stream going from a holding tank, through 1" hose, to a nozzle? I'm looking for something that might help with...

So the bugs here are finaly lgetting to me. From buzzing around to these spiders building castles everywhere. Have anyone ever built their own fogger/mist system for under a porch I see systems all the time that start at over $2000.00. It seems the most expensive parts are the nozzles...

I broke the yoke on my howse 5' deck and it appears I'll need to replace not only that, but the u-joint, and the yoke welded on to the triangle shaft heading towards the pto. The yoke on the mower is 1 3/8" with a shear bolt. If I can get the 2 yokes and u-joint without replacing the entire...

My latest aquisition of a Cummins C112 drill press has me needing a vise to mount on the drill table. Does anyone have any good recommendations? I've thought about getting a milling style vise, but the inability of being able to drill through the material due to the vise being in the way is a...

I was forunate enough to pick up an old Cummins C112 drill press this weekend for a song. The only thing wrong with it is cosmetic: all of the chrome plated or steel aprts have surface rust on them. I'm slowly taking these parts off and getting the rust off then putting a light coat of 30...

After taking a broom to my wrap around porch for the umpteanth time followed by the pressure washer, I'm ready for a spray control system. Being that I have almost 400' of porch, I'm getting quotes that are approaching $3000.00. Most of that is in the spray tips and high end pump. Has...

I've got a 80 gallon IR compressor that I still have sitting on teh original shipping pallet. I've thought about adding casters to it so at least I can move it aroudn the shop to clean behind and underneath, but it would appear that it might be a bit too top heavy without the outriggers like...

Good morning! TGIF! I just got a new 20 gallon parts washer and am looking for a source ( read cheap ) for mineral spirits. The big box stores are selling it for about $10.00 a gallon ( geesh ) :eek: Anyone offer any suggestions on where to purchase 20 to 30 gallons, even in bulk? Thanks

Does anyone by chance found any non oem filter numbers for all of the filters for a 300dtc? Air, fuel, hydraulic, and oil? Thanks

I have a 30x50x12 steel Mueller building with a 10x12 opening and a walk through door both on one end. I am in the process of wiring it for electrical and the next step is finishing off some of the walls for a work bench/tool storage and eventually a conditioned space office across the back...

My shop is finally getting a meter panel now that my "lein holder" has decided to approve my easement. So my question is: Where is the least expensive place to get all of my electrical supplies: Wire Breakers Conduit Boxes Recepticals I figure that Lowes and HD are probably the most...

For all of the time I have been on here, I've never posted a project. So, I thought I'd share what I got accomplished this past weekend. Nothing fancy, but it felt really good once I was finished. About 7 years ago, I aquired an old work table that had been left out in the weather several...

She saw one at a furniture store that she likes. It's made of aged cedar 4" fence pickets. Looks to be 40" or so tall. The shop owner didn't let me take pictures or measurements so I'm kinda screwed there. I've tried to search for plans to no avail. Anyone out there know of what I'm talking...