Recent content by Andy4600

I need to replace my front tires on my Ford 4600. They tires on there now are Goodyear 6 ply 4 rib tires. I have no idea how old they are, and they are hard as a rock. They have no tread left, and the cracks in them are getting disturbing. They are 7.5-16. I am looking at either the Firestone...

I wanted to see if anyone could identify this hydraulic cylinder...as in who made it, or what it was originally installed on. It came off my 735 loader for the bucket...but I have determined it is not original to the loader. Apparently, someone swapped the bucket and bucket hydraulic cylinders...

Has anyone replaced the bucket cylinders on their 735 loader with aftermarket cylinders? If so, what brand/size did you end up using? I'm currently looking at the following: Magister WCT 2.5x24 (2.5" bore, 24" stroke, 32" closed, 56" open) InternationalHydraulicsusa IMW-2524 (2.5" bore, 24"...

I need some help identifying the bucket cylinder and/or the appropriate rebuild kit for my Ford 735 loader. The loader is on my Ford 4600 tractor. Loader has a small plate marked 19-525. I bought a shop manual and parts manual to try and identify the cylinders. I was able to identify my lift...

I need to replace one of my tractor rear remote break away couplings due to excess leakage. I was looking at the pioneer 9500-4 Hydraulic Break-Away Coupling Kit? Anyone use one? Are they easy to use? What are the levers for? Are they ball valves for isolation? Here is what it looks like: Thanks

Ok, so I decided to change the oil in my rear axle/hydraulic system in my Ford 4600. I had not done this before, as I haven't had the tractor very long. My manual says to use 33.9 quarts of oil, and gives me a location for the oil level plug, to check level. First problem: My tractor oil level...

I am looking to get a Skid Steer Conversion adapter to convert my pin on Front End Loader to the SSQA system. I already know it is a good idea. I need some help comparing 2 models. They are: 1) WR Long Adapter (From Everything Attachments): W.R. Long Pin on Tractor Loader Bucket to Universal...

I'm about to pull the trigger on a Grapple/Root Rake for my Ford 4600. The tractor is 52 Hp PTO and 60 HP engine. FEL is a FORD 735, with a new hydraulic pump. I am lloking at the following: 1) The Rake Shop Light Class Rake Grapple: www.TheRakeShop.com / Root Rakes Grapples Attachments & Skid...

As the title says. How effective are grapples with 2 hydraulic tops, such as the rake shop grapple shown here www.TheRakeShop.com / Root Rakes Grapples Attachments & Skid Steers at back dragging? I would think too much debris would get by the top teeth, but thought I would ask.

Hi all, I need to clean up several acres (20+) of 3 year old cutover. Regrowth is minimal and most stumps are showing some rot. I am considering getting a W.R. Long adaptor plate to convert my 735 loader to the Universal attachment system, and then pick up a couple of "useful" attachments...

I bent my lift arm leveling yoke rod (the right side, without the crank) doing some grading with a blade on my 4600. The part numbers on the lift arm do not match the ones listed for a 4600 according to Hew Holland. New Holland lists a Cat II Lift arm yoke only, with a 13/16" shaft, for the...

Anyone have any experience with the aftermarket cast iron oil pans to replace the stamped steel oil pans? This is what I am talking about: S.60754 OIL PAN, CAST IRON, C9NN6675A And this is a comparison of the two types: Search results for: 'C9NN6675A'

Hi, I need to replace my oil pan on a 4600 Ford Diesel due to some unfortunate encounters with some large brush when brushhogging, causing a leak. I ordered an aftermarket pan, and the thing is painted blue inside the pan...at least on the gasket surface and sidewalls. The bottom isn't painted...

Hi everyone, I'm here hoping to learn more about my tractor. I'm a tractor novice, so I need all the help I can get.