lostcreekranch
Super Member
- Joined
- Dec 14, 2012
- Messages
- 7,948
- Location
- Austin County, Texas
- Tractor
- NH TL-100A with Bush Hog 5045 FEL, WR Long 3rd function, LS XR4155HC w/FEL, WR Long 3rd Function.
Drew .. prayers for quick and complete healing.
Good morning!!!!
- Thread starter 300UGUY
- Start date
- Views: 17255737
lostcreekranch
Super Member
- Joined
- Dec 14, 2012
- Messages
- 7,948
- Location
- Austin County, Texas
- Tractor
- NH TL-100A with Bush Hog 5045 FEL, WR Long 3rd function, LS XR4155HC w/FEL, WR Long 3rd Function.
NASA / SpaceX Launch just scrubbed about 17 minutes before launch. Next launch window is this Saturday afternoon.
History delayed .. for three days.
History delayed .. for three days.
Buppies
Super Star Member
- Joined
- Oct 26, 2011
- Messages
- 12,210
- Location
- SouthWestern Virginia
- Tractor
- Kubota L5240 EX mark 60 in 29 hp Toro 60inch Z Master 21 inch walk behind Polaris 900 hunter edition 30in toro walk behind
Drew glad to hear from you take it easy follow doctors orders and get well soon prayers sent
buckeyefarmer
Epic Contributor
Wonder if it is real or counterfeit?
buckeyefarmer
Epic Contributor
Welcome back!!!! Good to hear from you!!!!
toppop52
Super Star Member
- Joined
- Oct 19, 2011
- Messages
- 10,619
- Location
- Eastern Shore of Maryland
- Tractor
- Massey Ferguson 1723, Cub Cadet 1864
Got to 84 and heat index of 92, it was hot mowing grass! It’s still very dusty here, we had rain but days of 20-40 mph winds dried it up in a hurry.
I timed my mowing so I could watch the launch that wasn’t. Oh well, maybe Saturday.
We have what appears to be a dog pooping in the new stone garden and Ellen is pissed. Scat is wrong for a fox or coyote but it’s happening overnight, twice so far. Going to put one of the cameras up here and see what we see.
I’m covered in dust so off to the shower before dinner.
Have a good one.
I timed my mowing so I could watch the launch that wasn’t. Oh well, maybe Saturday.
We have what appears to be a dog pooping in the new stone garden and Ellen is pissed. Scat is wrong for a fox or coyote but it’s happening overnight, twice so far. Going to put one of the cameras up here and see what we see.
I’m covered in dust so off to the shower before dinner.
Have a good one.
Thomas
Epic Contributor
- Joined
- Apr 6, 2000
- Messages
- 31,077
- Location
- Lebanon,NH.
- Tractor
- Kubota B2650HSD w/Frontloader & CC LTX1046 & Craftman T2200 lawn mower.
Strong thoughts for you Drew...strong thoughts.
rswyan
Super Star Member
- Joined
- May 12, 2004
- Messages
- 11,396
- Location
- Northeast Ohio
- Tractor
- Kubota B2910, Cub Cadet Pro Z 154S, Simplicity 18 CFC, Cub Cadet 782
Well that adventure went about as well as might be expected ... 
Tried tapping the spanner wrench in and definitely a no-go ...
Hunted up a 3/16 drill bit and used it to kiss the end of hole ... just to see how much bigger the 3/16 pin was than the hole: turns out ... quite a bit ...
Then I dug up a 5/32 bit to see if it would fit in the hole.
Yup, no problem.
Soooo ... it turns out the next size down wrench McMaster offers uses 1/8" pins (not 5/32) ... and only has a range up to a 2" diameter cylinder (these are just slightly larger OD - probably a metric thing)
Fortunately, I can order up to 18:15 (Mon-Thu) and still get it next day from the local McMaster warehouse for normal shipping rates ... and they had it in stock.
Could have picked up a similar tool (Proto brand) from the local Grainger (which is much closer) for a little less money overall, if I wanted to dick around with driving over there (probably about 12 miles one way)
Nah, I'll pass ...
Lesson learned:
Probably wanna take a little more care on determining the actual hole diameter ... rather just assuming that what I think it is, is what it actually is ...
Now if I can only remember it ... :laughing:
Tried tapping the spanner wrench in and definitely a no-go ...
Hunted up a 3/16 drill bit and used it to kiss the end of hole ... just to see how much bigger the 3/16 pin was than the hole: turns out ... quite a bit ...
Then I dug up a 5/32 bit to see if it would fit in the hole.
Yup, no problem.
Soooo ... it turns out the next size down wrench McMaster offers uses 1/8" pins (not 5/32) ... and only has a range up to a 2" diameter cylinder (these are just slightly larger OD - probably a metric thing)
Fortunately, I can order up to 18:15 (Mon-Thu) and still get it next day from the local McMaster warehouse for normal shipping rates ... and they had it in stock.
Could have picked up a similar tool (Proto brand) from the local Grainger (which is much closer) for a little less money overall, if I wanted to dick around with driving over there (probably about 12 miles one way)
Nah, I'll pass ...
Lesson learned:
Probably wanna take a little more care on determining the actual hole diameter ... rather just assuming that what I think it is, is what it actually is ...
Now if I can only remember it ... :laughing:
Thomas
Epic Contributor
- Joined
- Apr 6, 2000
- Messages
- 31,077
- Location
- Lebanon,NH.
- Tractor
- Kubota B2650HSD w/Frontloader & CC LTX1046 & Craftman T2200 lawn mower.
94F very light breeze yep the 3H's today.
Today been slow motion day did just enough I think to earn my dinner :confused3: got critter food,putter in basement,need to water garden plan to set on deck as the sunsets waiting for night maybe critters.
Enjoy the weekend all.
Today been slow motion day did just enough I think to earn my dinner :confused3: got critter food,putter in basement,need to water garden plan to set on deck as the sunsets waiting for night maybe critters.
Enjoy the weekend all.
LouNY
Super Star Member
- Joined
- Jul 4, 2015
- Messages
- 12,311
- Location
- Greenwich, NY
- Tractor
- Branson 8050, IH 574, Oliver 1550 Diesel Utility (traded in on Branson) NH 8160. Kioti CK2620SECH
The gland end could have handled being drilled out that bit most likely.
Good luck with it, I had to make a gland wrench for a Dynahoe cylinder that hadn't been unscrewed since it was built in the 60's, drill rod and half inch flat stock with a 6 foot handle and it still took some sledge hammer persuasion.
Good luck with it, I had to make a gland wrench for a Dynahoe cylinder that hadn't been unscrewed since it was built in the 60's, drill rod and half inch flat stock with a 6 foot handle and it still took some sledge hammer persuasion.
